background image

www.totemmaker.net

Totem MiniLab

!

 

Fig. 7 Programmable output voltage 

Middle  display  is  used  for  showing  the  current  output  voltage  for  the  active  channel, 
which itself is indicated by the middle column of LED’s. Pressing middle SELECT button 
allows you to change the active channels. To edit currently preset voltage, SELECT button 
must  be  held  until  LED  starts  blinking.  Then  SET+  and  SET-  buttons  can  be  pressed  to 
adjust currently selected channels voltage. All other inactive channels still keep the same 
preset voltage until it’s changed by SET buttons on the side of the board. 

Example 

1. Connect the 

DAC1

 output to the ± 5 V voltage measuring channel input. 

2. Using  middle  select  button  switch  the  current  output  channel  until 

DAC1  Out

  LED 

lights up. 

3. Using left select button switch the measure channel to ± 5 volts. 

4. Hold 

SELECT

 button until 

DAC1 Out

 LED starts to blink.  

5. Using 

Set+

 and 

Set-

 button change the output value of the DAC1 channel. 

6. Observe that voltage measure display follows the same value as the DAC output one. 

!

 of 

!

10

31

Summary of Contents for Totem MiniLab
































Reviews: