manualshive.com logo in svg

U-Line H-2268, Manual

Share
Download
U-Line H-2268 Manual Download Page 7

0715 IH-2268

PAGE 7 OF 7

π

  CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA

1-800-295-5510

uline.com

OPERATING ISSUE

RECOMMENDATIONS

Belts continue to break.

1.  The agitator bar should be positioned so the belt lines up 

with the grooves on the bottom frame of the vacuum.

2.  Ensure that vacuum is set to correct carpet height setting. 

If there is little or no suction.

1.  There may be a clog in the hose. Take the hose apart at 

the top and bottom and remove the clog.

2.  Clean or replace the HEPA filter assembly and/or 

pre-motor filter.

3.  Ensure that vacuum is set to correct carpet height setting.

4.  Check suction control valve to ensure it is set correctly. 

Can be set to Hose or Floor Cleaning.

Vacuum turns off while in use.

1.  The machine may turn off due to overheating. 

2.  Check to make sure nothing is caught on the brush roll 

and check for clogs.

3.  You will need to press the reset button to restart the brush.

Vacuum has a burning smell.

1.  The belt may be damaged or something may be caught 

in the brush roll.

2.  Check brush roll for obstruction.

3.  Replace belt.

Brushes aren't turning.

1.  Check suction control valve to ensure that it is turned to 

floor cleaning.

2.  Make sure vacuum is lowered into cleaning position. (Will 

not spin in upright storage position.)

TROUBLESHOOTING

Summary of Contents for H-2268








Reviews:

No comments

Brands by name

Popular brands

Load more brands