background image

 

15 

SAW MAINTENANCE 

 

Maintenance interval 

Wath to do for maintenance and care 

After ecery use ot the 

machine 
 

Remove dirty water from container. 

Remove dirt and mud from the bottom of the container 

Rinse teh immersion pump with fresh water to prevent water 

pump dogging from residual dirt.  

After wet clearing and 

before using the machine 

again 

Connect the machine to an electric power outlet equipped with 

a“GFI” safety power breaker. If the safety power breaker cuts off 

the electrical power supply, do not try to operate the machine but 

have it checked by an authorized dealer first. 

Before not using the 

machine for a prolonged 

period of time 

Clean and lubricate all movable part. 

Before not using the 

machine for a prolonged 

period of time 

Check that the stand is safely fixed. 

Check that all screw joints and nuts are fixed. 

Check that the roller table is in its guides and that it easliy 

moves to and fro. 

With the saw blade removed, switch on the motor for an 

instant and switch it off again. If the motor does not run, have 

the machine inspected by a qualified electrician. 

Check that the immersion pump works properly. Turn on the 

cooling water tap and switch the machine on. If the pump 

does not give any water or only a little, switch the machine off 

at once. Clean the pump, or replace if necessary. 

Ambient temperture below 

0°C (operation in winter) 

To prevent the water in the pump and cooling system from 

freezing, remove the water after using the machine or when there 

will be a long break. Make sure that the cooling system is entirely 

drained so that there is no water left inside the pump, water hose 

and bearing housing 

 

 

 

 

 

For your safety, before performing any maintenance on the saw turn off 

the power switch and unplug the power card 

 

 

 

 

 

 

Summary of Contents for TBE400
































Reviews: