background image

 

http://www.tyan.com

 

13

Table of Contents 

 

Chapter 1: Overview....................................................................... 15

 

1.1   About the TYAN FT48T-B7105 .............................................. 15

 

1.2   Product Models ....................................................................... 16

 

1.3   Features 

.................................................................................. 17

 

1.4   Standard Parts List ................................................................. 25

 

1.4.1   Box Contents ................................................................... 25

 

1.5   About the Product ...................................................................  26

 

1.5.1   System Front View .......................................................... 26

 

1.5.2   System Rear View ........................................................... 29

 

1.5.3   System Top View ............................................................. 32

 

Chapter 2: Setting Up ..................................................................... 35

 

2.0.1   Before you Begin ............................................................. 35

 

2.0.2   Work Area ........................................................................ 35

 

2.0.3   Tools ................................................................................ 35

 

2.0.4   Precautions ......................................................................  36

 

2.1   Installing Motherboard Components ...................................... 37

 

2.1.1   Removing the Chassis Cover ..........................................  37

 

2.1.2   Opening the Chassis Front Bezel ....................................  39

 

2.1.3   Installing the CPU and Heatsink ......................................  40

 

2.1.4   Installing the Expansion Cards ........................................  43

 

2.1.5   Installing the Memory ...................................................... 46

 

2.1.6   Installing Hard Drives ...................................................... 49

 

2.1.7   Installing the DVD-ROM .................................................. 51

 

2.2   Installing Foot Stands ............................................................. 54

 

2.3   Rack Mounting ........................................................................  56

 

2.3.1   Installing the FT48T-B7105 in a Rack ............................. 56

 

Chapter 3: Replacing Pre-Installed Components ........................ 61

 

3.0.1   Introduction ......................................................................  61

 

3.0.2   Disassembly Flowchart 

.................................................... 61

 

3.1   Removing the Cover ............................................................... 62

 

3.2   Replacing the System Fan ..................................................... 62

 

3.3   Replacing the Fan Board ........................................................  63

 

3.3.1   Fan Board Features 

......................................................... 65

 

3.3.2   Pin Definitions ..................................................................  66

 

3.4   Replacing the HDD Backplane Board .................................... 67

 

3.4.1   HDD BP Board Features ................................................. 68

 

3.4.2   Connector Pin Definitions ................................................  69

 

3.5   Replacing the Front Panel Board ........................................... 70

 

3.5.1   Front Panel Board Features ............................................ 72

 

Summary of Contents for FT48T-B7105





























































































Reviews: