background image

 

1.12. All  service  work,  particularly  filter  changes,  must  be  carried  out  in  accordance  with  the 

manufacturer’s service schedule. Failure to comply will invalidate the warranty. In the event of 
a claim, proof of the service work being carried out may be required. 

1.13. Repeat or additional repairs resulting from incorrect diagnosis or poor quality previous repair 

work are excluded from warranty. 

 

NB  Warranty  cover  will  be  invalid  if  any  non-genuine  parts  have  been  fitted  or  used.  Use  of  non-

genuine parts may seriously affect the machine’s performance and safety. McConnel Ltd cannot be 
held responsible for any failures or safety implications that arise due to the use of non-genuine parts. 

 
 

2. 

REMEDIES AND PROCEDURES 

 

2.01. The  warranty  is  not  effective  unless  the  Selling  Dealer  registers  the  machine,  via  the 

McConnel  Ltd  web  site  and  confirms  the  registration  to  the  purchaser  by  completing  the 
confirmation form in the operator’s manual. 

2.02. Any  fault  must  be  reported  to  an  authorised  McConnel  Ltd  dealer  as  soon  as  it  occurs. 

Continued  use  of  a  machine,  after  a  fault  has  occurred,  can  result  in  further  component 
failure for which McConnel Ltd cannot be held liable. 

2.03. Repairs  should  be  undertaken  within  two  days  of  the  failure.  Claims  submitted  for  repairs 

undertaken  more  than  2  weeks  after  a  failure  has  occurred,  or  2  days  after  the  parts  were 
supplied  will  be  rejected,  unless  the  delay  has  been  authorised  by  McConnel  Ltd.    Please 
note that failure by the customer to release the machine for repair will not be accepted as a 
reason for delay in repair or submitting warranty claims. 

2.04. All claims must be submitted, by an authorised McConnel Ltd Service Dealer, within 30 days 

of the date of repair. 

2.05. Following  examination  of  the  claim  and  parts,  McConnel  Ltd  will  pay,  at  their  discretion,  for 

any  valid  claim  the  invoiced  cost  of  any  parts  supplied  by  McConnel  Ltd  and  appropriate 
labour and mileage allowances if applicable. 

2.06. The submission of a claim is not a guarantee of payment. 
2.07. Any decision reached by McConnel Ltd is final. 

 
 

3. 

LIMITATION OF LIABILITY 

 

3.01. McConnel Ltd disclaims any express (except as set forth herein) and implied warranties with 

respect to the goods including, but not limited to, merchantability and fitness for a particular 
purpose. 

3.02. McConnel Ltd makes no warranty as to the design, capability, capacity or suitability for use of 

the goods. 

3.03. Except  as  provided  herein,  McConnel  Ltd  shall  have  no  liability  or  responsibility  to  the 

purchaser or any other person or entity with respect to any liability, loss, or damage caused 
or  alleged  to  be  caused  directly  or  indirectly  by  the  goods  including,  but  not  limited  to,  any 
indirect, special, consequential, or incidental damages resulting from the use or operation of 
the  goods  or  any  breach  of  this  warranty.  Notwithstanding  the  above  limitations  and 
warranties, the manufacturer’s  liability hereunder for damages incurred by the purchaser or 
others shall not exceed the price of the goods. 

3.04. No  action  arising  out  of  any  claimed  breach  of  this  warranty  or  transactions  under  this 

warranty may be brought more than one (1) year after the cause of the action has occurred. 

 
 

4. 

MISCELLANEOUS

 

 

4.01. McConnel  Ltd  may  waive  compliance  with  any  of  the  terms  of  this  limited  warranty,  but  no 

waiver of any terms shall be deemed to be a waiver of any other term. 

4.02. If  any  provision  of  this  limited  warranty  shall  violate  any  applicable  law  and  is  held  to  be 

unenforceable,  then the invalidity  of  such  provision  shall  not  invalidate  any  other  provisions 
herein. 

4.03. Applicable law may provide rights and benefits to the purchaser in addition to those provided 

herein. 

Summary of Contents for TP5750























































Reviews: