TWIG Neo Quick Manual Download Page 5

Processing. An operation is in progress, please wait.

General failure. Displayed when an operation fails. E.g. if you try to make a call when there 

is no number pre-configured in the device. Simultaneously, the failure tone is played.

SIM failure. Displayed when there is no SIM card inserted in the device, or if the PIN code 

was rejected. Simultaneously, the failure tone is played.

Retry or discard icon is displayed when e.g. SRD tag is read and the transmission of data 

fails. Pressing the SEND/F1 key retries and the END/F2 key discards.

Battery low. Displayed when there is a need to recharge the battery (or replace it with 

another recharged battery). Simultaneously, the battery low tone is played.

The device is connected to a charger. Settings during battery loading take place. 

Simultaneously, the charging tone is played.

The device is disconnected from the charger. Settings during battery loading are ended, 

the device returns to normal operation.

The device is charging and the battery is still too empty to restart the device.

Battery is too low to charge. This symbol is displayed when initial charging of empty battery 

is ongoing and user tries to turn device on. Device will turn on after a while.

Normal incoming call. If available, the name associated with the calling number/the phone 

number itself is displayed on the bottom. Displayed until the call is answered (to answer, 

press SEND/F1 key).
Initiating information call or position report. Press the SOS key and hold it down while this 

notification is displayed.

Sending a position report. Simultaneously, the message sending tone is played.

Making an information call. Displayed until the call is answered.

A call is in progress. Displayed while the call is connected.

Starting SOS cycle (a long press): Emergency tone settings are switched on. Press the SOS 

key and hold it down until the wedges are all turned black.

Starting SOS cycle (two quick presses): Press the SOS key briefly. Emergency tone settings 

are switched on. Press the SOS key again when the second circle starts blinking.

SOS cycle cancellation period. A countdown timer is displayed. The timer counts the 

cancellation time left (in seconds). Simultaneously, the cancellation tone is played. To 

cancel the SOS cycle, do it while this notification is displayed (by pressing the END/F2 key).

Emergency cancellation. Displayed right after the SOS cycle was cancelled.

Emergency completion. Displayed when the SOS cycle ends normally, or when the 

emergency mode is ended manually.

Emergency call retry. Emergency numbers can be voice call numbers. The notification is 

displayed when the device makes another call attempt to a number.

Emergency mode/Working. The device is through with emergency calls, but sending 

messages, message confirmation or position refresh is still going on.

Emergency confirmation message received. After receiving confirmation, the device will 

end resending of an emergency message. Simultaneously, the message reception tone is 

played.
Post-emergency mode. The GSM operator´s name is replaced by the emergency cycle icon. 

While this notification is displayed, the device can be tracked by emergency numbers, also 

emergency tone and display settings are kept on. This mode can be terminated manually, 

by pressing the END/F2 key.
Network emergency call query. Displayed when the SOS key is pressed but making SOS 

cycle is NOT possible (e.g. SIM card is missing or roaming network is not available). You 

may still try to make network emergency call by pressing SEND/F1 key. You can also exit 

the query without making an emergency call by pressing END/F2 KEY.
Pre-alarm for ManDown alarm is not set. Displayed when “the cancel timer” is not 

configured, and SOS cycle starts right away. To mute the audible alert tone, press the END/

F2 key.
Pre-alarm for ManDown alarm is set. The countdown timer shows that you still have 27 

seconds time left to cancel the sensor alert if you want. To cancel the SOS cycle, lift the 

device to vertical position. Do it while this notification is displayed. To let the SOS cycle take 

place: Do nothing. To mute the audible alert tone, press END/F2 key.

Alert state ended. Displayed right after the emergency cycle is finished, or the sensor alert 

is cancelled.

Post-alarm state. Displayed when the emergency cycle is completed, and the device 

makes audible alarms at regular intervals. You can receive phone calls and answer them 

by pressing SEND/F1 key. In order to stop the post-alarm tone, the device must be lift up 

to vertical position.
Pre-alarm cancel. Displayed when pre-alarm cancel is enabled. When enabled, user 

can cancel ManDown pre-alarm, triggered by change of orientation or no movement, by 

pressing END/F2 key.
Ripcord connected. Displayed when the ripcord adapter is connected to ripcord hole 

magnet towards the inner part of the device (Available only in TWIG Neo).

ICONS DISPLAYED IN THE MIDDLE OF THE SCREEN

Summary of Contents for Neo








Reviews: