Tuthill SDV Series Operator'S Manual Download Page 12

Page: 12 / 58

Introduction

Manual 1861 Rev C p/n 001861 0000

SPECIFICATIONS

MODEL

SDV-800

SDV-1500

SDV-2700

50 Hz

60 Hz

50 Hz

60 Hz

50 Hz

60 Hz

Nominal displacement

capacity

368 CFM

(625 m³/hr)

441 CFM

(750 m³/hr)

765 CFM

(1,300 m³/hr)

882 CFM

(1,500 m³/hr)

1,324 CFM

(2,250 m³/hr)

1,588 CFM

(2,700 m³/hr)

Ultimate pressure

0.03 Torr

0.01 Torr

0.1 Torr

0.05 Torr

0.1 Torr

0.05 Torr

Motor

20 HP (15 kW)

50 HP (37 kW)

75 HP (55 kW)

Power connection type

C-flange

Bare shaft

Minimum Speed

1,800 RPM

Speed

2,900 RPM

3,500 RPM

1,450 RPM

1,750 RPM

1,450 RPM

1,750 RPM

Port size 150 # FF

Inlet

Outlet

4 in. (10.2 cm)

2.5 in. (6.4 cm)

5 in. (12.7 cm)

3 in. (7.6 cm)

6 in. (15.2 cm)

4 in. (10.2 cm)

Gear oil

(1)

0.58 gal (2.2 L)

1.85 gal (7 L)

2.38 gal (9 L)

Grease

3.9 oz (110 g)

6 oz (170 g)

8.8 oz (250 g)

Cooling water @ 68°F (20°C)

(2)

5.3 GPM (20 LPM)

9.5 GPM (36 LPM)

12.7 GPM (48 LPM)

Cooling purge

(3)

None

94.1 SCFM (160 Sm³/hr)

100 SCFM (170 Sm³/hr)

Maximum water jacket

pressure rating

100 PSIG

Liquid Handling Capacity

2.5 Gallons per min

Maximum particle size

45 micron or below

Ambient temperature range *

0°F - 104°F

Maximum discharge pressure

rating PSIG / BarG

5 / 0.3

3 / 0.2

Discharge temperature

<455°F (235°C)

<482°F (250°C)

<500°F (260°C)

Maximum design

temperature, inlet gas

122°F (50°C)

Maximum design temperature,

discharge gas

572°F (300°C)

Maximum design

temperature, oil

158°F (70°C)

Maximum design

temperature, grease

176°F (80°C)

Maximum design

temperature, cooling water

95°F (35°C)

Noise

(4)

85 dBA

90 dBA

Weight

1,212 lb (550 kg)

2,970 lb (1,350 kg)

3,640 lb (1,650 kg)

Dimensions, L x W x H

(5)

44.5 × 18.9 × 15.3 in.

(1,131 × 479 × 389 mm)

59.6 × 25.0 × 20.8 in.

(1,513 × 635 × 529 mm)

66.3 × 26.9 × 23 in.

(1,684 × 683 × 585 mm)

(1)

The above listed amount of oil is for reference only. Fill oil to the top

level of the red mark or OL Mark. Special inert oils are available for

hazardous applications.

(2)

The above listed amount of cooling water is based on water

temperature of 68°F (20°C). The amount of water varies when using

an After Cooler. Temperature differential between cooling water

supply temperature and discharge temperature shall be

maintained below 12.6°F (7°C).

(3)

The cooling purge flow rates are at standard conditions.

(4)

Noise levels are based on the pump equipped with an exhaust

silencer and are from 3 ft (1 m) away from the pump.

(5)

Dimensions are for bareshaft pump (without motor) only.

* If water is cooling medium then minimum temperature should be 32°F.

Table 1-2

Summary of Contents for SDV Series



























































Search results

Summary of Contents for SDV Series

Reviews:

Tuthill SDV Series, Operator'S Manual, Page: 12 / 58

Search results

Summary of Contents for SDV Series

Reviews: