© Trynex International 2012
24
Maintenance
Break-in Service
(first 10 hours) Checklist
• Change engine oil
• Change Clutch oil
• Grease all fittings
• Check tire pressure
• Check wheel lug nut tightness
• Check tightness of Pivot Bolts and Nuts
• Test Safety Devices
• Check Drive belt tension
• Check Spinner/Pump belt tension
Every 50 hours (or every 2 weeks) Checklist
(Perform more frequently if operating in wet or dusty conditions)
• Grease all fittings
• Clean air filter
• Check tire pressure
• Check wheel bolt lug nut tightness
• Check tightness of Pivot Bolts and Nuts
• Test Safety Devices
• Check drive belt and spinner/clutch belts
Every 100 hours (or monthly) Checklist
(Perform more frequently if operating in wet or dusty conditions)
• Change engine oil
• Change Clutch oil
• Clean or replace air filter
• Check engine manual for additional service required
• Grease all fittings
• Check tire pressure
• Check wheel lug nut tightness
• Check tightness of Pivot Bolts and Nuts
• Test Safety Devices
• Check drive belt and Spinner/Pump belts, replace if necessary
• Flush and clean Spray tanks
• Calibrate Spray System
• Calibrate Spreader System
Yearend checklist
•
Read Safety Manual WARNINGS
• Change engine oil
• Change Clutch oil Clean or replace air filter
• Check engine manual for additional service required
• Grease all fittings
• Check tire pressure
• Check wheel lug nut tightness
• Check tightness of Pivot Bolts and Nuts
• Test Safety Devices
• Check drive belt and spinner/clutch belts, replace if necessary
• Flush and clean Spray tanks
• Run RV anti-freeze or Windshield washer solution through spray
system
• Calibrate Spray System
• Calibrate Spreader System
IMPORTANT: Keeping the RS7200 Ride N Spray operating reliably
requires attention to maintenance. Proper maintenance prevents
damage to your machine and preventable malfunctions. Proper
maintenance is required for the safe operation of the machine.
Use the following timetables to perform routine maintenance.
Engine Service Intervals
Refer to Engine Manual included with this machine for Engine service
intervals.
IMPORTANT: Change engine and clutch oil every 100 hours.
Daily Service Checklist.
IMPORTANT: Adjust, repair, replace, and report any irregularities
discovered during these checklist inspections to your supervisor.
• Clean machine in a designated area. IMPORTANT: DO NOT power
wash machine. High pressure water will force corrosive fertilizer
residue into bearings, linkages, and other parts. Corrosion
damage is not covered by the Warranty. Instead use low pressure
air regulated to 29 PSI. Once a week, or as necessary, use low
pressure water regulated to 29 PSI to wash machine. Start and
run machine and blow dry to remove any water.
• Empty Hopper. NOTE: Use a dedicated pail or wet /dry vacuum to
remove fertilizer so that it can be recycled
• Clean:
•
Spinner Platter.
• Footpads.
• Nozzles and Nozzle Strainers, If necessary.
• Hopper opening plate, Auxiliary Gate Slide plate and linkage.
• Engine cooling fins, Blower housing inlet (Starter), carburetor,
governor linkage, Honda Throttle Lever, Throttle Lever and cable.
• Lubricate and protect the following, using WD-40 or equivalent:
• Operating controls and cables.
• Hopper Opening Plate and Auxiliary Gate Plate.
• Carburetor and all linkages and springs.
• Exposed aluminum.
• Check and record Engine Idle Speed (Must not exceed 1650
RPM).
• Check and record Engine Top Speed ( Must be 3,450 RPM).
• Gage, record, and adjust Hopper control settings as necessary,
including:
• Auxiliary Gate Adjustment Plate.
• Hopper opening.
• Rate Adjustment Knob
• Check and adjust the Spray Nozzle alignment as necessary.
• Check and top off engine oil.
• Check and top off clutch oil.
• Check for loose or missing fasteners or parts, cracks in metal or
welds.
Read Safety Manual WARNING “Maintenance and Service”
before starting, operating, repairing or performing maintenance
on the RS7200.
