background image

8

85540-85541

INTENDED USE AND FUNCTION

The XT5 Aerator is a self-propelled coring tine 

type aerator. The XT5 Aerator is intended to be 

used  for  the  aeration  of  the  turf  at  a  properly 

prepared  worksite.  The  XT5  Aerator  is  NOT 

intended to be used for any purpose other than 

the  aeration  of  turf.  The  XT5  Aerator  is  NOT 

designed for or intended to accept riders.

DESCRIPTION OF OPERATOR POSITION 

(See Figure 2)

The operating position for the operator is located 

behind the handlebar. Do not engage any 

controls before moving to the operator position.

TO AVOID SERIOUS INJURY,

Move To the Operator’s Position Behind The Handlebar 

Before Engaging Any Operator Controls

DESCRIPTION OF OPERATOR CONTROLS

(See Figure 2)

The Operator Controls are located on the handlebar. They are 

the Transport Wheels Lift Handle and the Forward/Reverse 

Direction Control Handle. Engine controls are located on the 

engine.

Ensure  that  all  operator  controls  are  in  good  operating 

condition. Do not alter operator controls and/or operate the 

Aerator with defective or non-operational operator controls.

Description

DESCRIPTION

WARNING

FIGURE 2

HANDLEBAR

FORWARD/REVERSE

DIRECTION

CONTROL HANDLE

TRANSPORT

WHEELS

TINES AND TINE REEL

REMOVABLE

TRANSPORT WHEELS

LIFT HANDLE

LOCATION OF MAJOR

COMPONENTS

OPERATOR

POSITION

DEPTH

SETTING

STOP

DS85540-01 Rev B

WEIGHT

FRONT DRIVE WHEELS

NEUTRAL CONTROL KNOB

FRONT TIE DOWN LOCATIONS

REAR TIE DOWN

LOCATIONS

ENGINE

THROTTLE &

FUEL SHUTOFF

ON/OFF

SWITCH

YAMAHA ENGINE

CHOKE

YAMAHA

TRANSPORT

LOCKING

PIN

BRIGGS & 

STRATTON

Summary of Contents for 85540


















Reviews: