background image

13

85372

CLUTCH

CONTROL

HANDLE

REAR

TRANSPORT

WHEELS

LATCH

HANDLE

HANDLEBAR

(AS VIEWED FROM OPERATOR'S POSITION BEHIND HANDLEBAR)

RIGHT TURN STEERING

AND TRANSPORT “GO”

CONTROL LEVER

OP85372-03

LEFT TURN STEERING

AND TRANSPORT “STOP”

CONTROL LEVER

THROTTLE

FIGURE 9

●  To  engage  the  drive  you  simply  pull  back  on  the 

clutch bail and 

engage the right control

● To stop the machine when transporting let go of the 

right control and engage the left control.  
To  make  turns  while  transporting,  pull  back  on  the 

handlebar  to  reducing  traction  by  slightly  lifting  the 

front tires while pulling to the side you want to turn. 

When transporting with the TurnAer Chariot attached, 

be  aware  of  obstacles  and  increased  stopping 

distances.    Never  attempt  to  load  the TurnAer  while 

riding on the Chariot.
If you encounter a situation where you cannot maneuver 

the machine with the Chariot attached simply detach 

the Chariot, maneuver the TurnAer and re-attach the 

Chariot.

OP85372-06

TRANSPORT

TINES UP

TURN

RIGHT

TURN

LEFT

AERATE

TINES DOWN

FIGURE 8

OPERATION

Summary of Contents for 85372




















Reviews: