The device is designed, tested and approved for branch circuits up to 20 A
(UL) and 32 A (IEC) without additional protection device.
➤
If an external fuse is used, use B or C characteristic circuit breakers with at
least 6 A to avoid a nuisance tripping of the circuit breaker.
Operating
CAUTION
Hot surfaces
Burn risk
➤
Do not touch the housing during operation or shortly after power-off.
The green Status LED reports an output above 90% of the adjusted voltage.
Relay-OK contact
The Relay OK contact monitors the output voltage. If the contact is closed,
the Status LED green lights up green
Contact ratings:
■
60 VDC, 0.3 A
■
30 VDC, 1 A
■
30 VAC, 0.5 A for resistive loads
The device is safe in case of a single phase loss. An external protection is
not necessary. A disconnecting means shall be provided for the input of the
device.
LED bar and push-buttons
■
Monitoring mode (normal operation)
Actual output power = percentage of max. 500 W (100 % = 500 W)
Values above 100 % are shown in orange. By pressing the up and down keys,
the output power of the respective output is displayed in %. The orange LEDs
OUT1 and OUT2 indicate the selected output.
■
Configuration mode
Button [Voltage Set]
Hold for 3 s Configuration mode, all LEDs flash shortly.
Start mode: “Set output voltage”
The output voltage is set for both outputs.
Hold for 3 s,
press 1×
Mode ”Set tripping current”
The tripping current is set separately for both outputs.
Hold for 3 s,
press 2×
Select the other output (only for ”Set tripping current”)
Buttons [
] [
]
Set value
The set value for output voltage or tripping current is indicated via
the LED bar. All orange LEDs are off. The setting becomes effective
immediately.
Without further pressing the buttons, the LED bar will return from any other
mode to normal mode after 15 s.
Deactivating outputs
➤
Press the button at the output channel (OUT1 or OUT2) for at least 1 s to
activate or deactivate the output manually.
Maintenance
Clean the devices at regular intervals with a damp cloth.
Repair
The device must not be repaired by the user. Take defective devices out of
operation. Observe our return acceptance conditions when returning the
device to Turck.
Disposal
The devices must be disposed of correctly and must not be included in
general household garbage.
EN
Quick Start Guide
All values are typical figures specified at 3 × 400 VAC, 50 Hz input voltage, symmetrical
phase voltages, 24 V, 500 W output load, 25 °C ambient temperature and after a
5 minutes run-in time unless specified otherwise.
Outputs
Output voltage
24 VDC, nominal value
Adjustment range
24…28 VDC
Output power 24 V…28 V, continuous at ambient temperature:
– at 45 °C
480…560 W
– at 55 °C
480…500 W
– at 70 °C
350 W
Linear derating b45 °C and +70 °C (s. fig. 5)
Output currents
Up to 10 A, settable per output
Input
Input voltage AC
3 AC, 380… 480 V ±15 %
Mains frequency
50…60 Hz ±6 %
Input current AC
1.1/0.9 A at 3 × 400/480 VAC
Power factor
0.94/ 0.95 at 3 × 400/480 VAC
Input inrush current
1.5/1.5 A peak at 3 × 400/480 VAC,
temperature independent
Efficiency
Efficiency
95.8/95.6 % at 3 × 400/480 VAC
Losses
20.8/23.0 W at 3 × 400/480 VAC
Hold-up time
24/24 ms at 3 × 400/480 VAC
Ambient conditions
Temperature range
-25…+70 °C
Max. operating temperature
+70 °C, measured 2 cm below the device
Relative humidity
5…95 %
Housing
Dimensions (l × w × h)
183 × 182 × 59 mm, without connectors
Weight
1200 g/2.7 lb
Protection class
IP65/IP67, with all mating connectors
firmly connected
Protection against electrical, mechanical
and fire hazards
Hans Turck GmbH & Co. KG | Witzlebenstraße 7, 45472 Mülheim an der Ruhr, Germany | Tel. +49 208 4952-0 | Fax +49 208 4952-264 | [email protected] | www.turck.com
© Hans Turck GmbH & Co. KG | 100029123 2021-04 DE EN
PSU67-3P-1MP-2M5-24200-F
Technical Data
Wiring diagrams
1 = L1
2 = L
2
3 = L
3
4 = GND
3
2
4
1
(LONG)
1 = GND (V2)
2 = GND (V1)
3 = FE
4 = 24VDC (V1)
5 = 24VDC (V2)
5
4
1
2
3
Input 7/8“
Output 7/8“
1 = RELAY +
2 = n.c.
3 = n.c.
4 = RELAY -
5 = n.c.
3
4
1
2
5
M12 Relay-OK
