manualshive.com logo in svg

turck IO-LINK MASTER, User Manual, Page: 67 / 86

Share
Download
turck IO-LINK MASTER User Manual Download Page 67

Acyclic data exchange via PROFIBUS-DP C2-master and TURCK IO-Link DTM

D301171 -  IO-Link master 1108

5-2

Communication via DTM with C2-master

To be able to access the IO-Link master and the connected TURCK IO-Link sensors via 
TURCK IO-Link DTM, the usage of a PROFIBUS-DP master Class 2 (C2-master) is necessary.

The example described in the following shows, besides configuration, parameterization and 
diagnosis via DTM, also the measurement value representation for the IO-Link master or 
respectively for the connected TURCK-sensors.

Used hardware

„

TURCK-PB-XEPI (Ethernet/ PROFIBUS - interface), EtherNet/IP-address 192.168.1.23 

„

TURCK-IO-Link master SDPXIOL4-0001, DP-address 40 

–

IO-Link port 1 (slot 2): TURCK pressure sensor, PS100R-501-LI2UPN8X-H1141 

–

IO-Link port 2 (slot 3): not used

–

IO-Link port 3 (slot 4): Siemens ultra sonic sensor, PXS310C M18 IO-Link (6GR6333-
3KS00)

–

IO-Link port 4 (slot 5): not used

Used software

„

PACTware™, version 3.6

„

DTM for the PB-XEPI: CommDTM_PROFIBUS_DPV1 from Trebing & Himstedt, 
version 3.0.0.8

„

TURCK-DTM for the IO-Link master SDPX-IOL4-0001

„

TURCK-DTM for the TURCK-sensor PS100R-501-LI2UPN8X-H1141

The software PACTware™, the DTMs as well as the documentation for the devices can be 
downloaded free of charge from www.turck.com.

Hardware-configuration C2-master

The PB-XEPI is connected to the PC via EtherNet/IP. 

Default IP-address: 169.254.0.1

Subnet: 255.255.0.0

The connection to PROFIBUS is done via a SUB-female connector.

Summary of Contents for IO-LINK MASTER























































































Reviews:

No comments