Operation
9
Steam
Steam can be injected into the oven for a pre-determined length of
time ( from 1 sec to 9 secs).
Steam can be injected at any time during use.
In Program Mode, the steam time can be set to automatically
activate at the beginning of a stage for between 0 to 9 seconds.
Changing Steam Time (Manual Mode)
Press and hold the ‘Steam’ key until the ‘
Stx’
time is
displayed and flashing in the upper display.
Rotate the ‘Temp’ knob +/- to select the steam time
required (0 - 9 seconds).
Press ‘Steam’ key again to confirm the setting.
Moisture Mode - Optional Setting
(Refer ‘Controller-Operator Settings’ - ‘ESt = 2’)
Optionally, the oven can be set to operate at one of six levels of
pre-set moisture injection. (H-0 - H-5).
When Moisture Mode H-0 is selected, a shot of steam is
available whenever the oven is running, by pressing the ‘Steam’
key.
When Moisture Mode H-1 (Minimum) to H-5 (Maximum) are
selected, these moisture modes will only operate when a
program is running, Core Temp Probe Mode has been selected
or when a timer is running in Manual Mode.
Selecting Moisture Mode
Press ‘Steam’ key to activate Moisture Mode. ‘Steam’ key
LED will illuminate when Moisture Mode is ‘On’. Moisture
Mode will operate at the preset level during the cooking
cycle.
Changing Moisture Mode Level
Press and hold the ‘Steam’
Key until the
‘H-X’
level is
displayed and flashing in the upper display.
Rotate the ‘Temp’
Knob -/+ to select Moisture Mode level
required.
Press the
STEAM
Key to confirm setting.
The ‘Moisture’ Mode level can be changed at anytime during
operation by following the setting method as described above.
When setting Moisture level, consider the Oven Set
Temperature. If set BELOW 100°C (212°F), water may pool in
oven as temperature will be too low to create steam.
Core Temp Cooking Mode - Optional
An Optional Core Temp Probe Kit #236060 is available for
this oven.
This allows use of the Core Probe Cooking feature of this oven.
When the core probe is fitted to the connection point on control
panel side, the timer function and display becomes the core temp
probe temperature setting and display. Cooking completion is then
determined by the core temp probe reaching the set core probe
temperature.
To enable Core Probe Cooking Mode plug in the Core Probe.
The Timer Display will then change to '
CP' (Core Probe).
The Timer Knob function will then be for Core Temp setting.
To disable Core Probe Cooking Mode, unplug the Core Probe.
The Timer Display and Knob will return to time function.
Manual Mode
In Manual mode the ovens settings are.
- Temperature
- 60-260C / 140-500F.
- Timer setting
- 0-180min or Infinite.
- Fan Speed setting
- Hi / Lo.
- Steam setting
- 0 - 9 Seconds.
- Vent
- Open / Closed.
An Optional Core Probe can also be used in Manual Mode.
Program Mode
In Program Mode 30 Programs are able to be used.
In each program the following settings are possible.
- Temperature
- 60-260C / 140-500F.
- Time
- 0-180min or Infinite.
- Fan Speed
- Hi/ Lo.
- Steam
- 0 - 9 Seconds.
- Vent
- Open / Closed.
3 baking stages can also be set in each of the 30 programs.
- All settings can be changed between baking stages.
- At completion of each stage an end of stage alarm can also
be set.
Optional Core Probe can also be used in Program Mode.
Changing between Manual and Program Modes
Press ‘Program’ key to select Program Mode. The LED
will illuminate showing Program Mode now set.
Press ‘Program’ Key to return to Manual mode.
Fan Speed
This oven features a 2 speed fan.
Hi Speed - This is the default operating speed.
- Hi Fan should be used for most applications.
- Hi Fan provides the fastest cooking time and evenness
throughout oven.
Lo Speed - This is the optional setting.
- Lo Fan speed is selected using the Fan Lo key.
- Lo Fan should be used on delicate products such as
cake and muffin.
On start-up, the oven will always default to normal Hi speed fan.
Fan speed can be changed at any time during use.
In Program Mode, fan speed can be pre-set and each baking stage
can have a different fan speed.
Changing the Fan Speed
Press ‘FAN LO’ key to change to Lo Fan speed. LED will
illuminate showing Lo Fan speed is now set.
Press ‘FAN LO’ key to change back to Hi Speed fan.
Vent
This oven features an automatic oven vent. On Start-Up, the oven
will always default to ‘Vent Open’.
The vent position can be changed at any time during use.
In Program Mode, the vent position can be pre-set and each stage
can have a different vent position.
Changing the Vent Position
Press ‘VENT’ key to open vent. LED will flash whilst vent
is moving and will illuminate when vent is open.
Press ‘VENT’ key again to close the vent.
