background image

2

TABLE OF CONTENTS

INSTALLATION & OPERATION INSTRUCTION

 

GENERAL / RATING PLATE

 

CLEARANCE / CAUTION / HIGH SHELF ASSEMBLY

 

LEVELING / AIR SUPPLY & VENTILATION

 

GAS CONNECTION / MANUAL SHUT-OFF VALVE

 PRESSURE 

REGULATOR

 

60” RANGE REQUIRES TWO GAS CONNECTIONS

 RIGID 

CONNECTIONS 

 FLEXIBLE 

COUPLINGS

INITIAL PILOT LIGHTING

FINAL PREPARATION

CLEANING AND MAINTENANCE

WARRANTY INFORMATION

3

4

5

6

6

7

8

8

9 - 10

11

12 - 13

14

PAGE

SHIPPING DAMAGE CLAIM PROCEDURE

The equipment is inspected & crated carefully by skilled personnel before leaving factory. The transportation company 
assumes full responsibility for safe delivery upon acceptance of this equipment if shipment arrives damaged ;

1. VISIBLE LOSS OR DAMAGE : 

Note on freight bill or express delivery and have signed by person making delivery.

2. FILE CLAIM FOR DAMAGES IMMEDIATELY : 

regardless of extent of damages.

3. CONCEALED LOSS OR DAMAGES : 

If damages are noticed after unpacking, notify transportation company 

immediately and file “Concealed Damage” claim with them. This should be done within fifteen(15) days from date 
delivery is made to you. Return container for inspection.

German Knife Inc

4184 E. Conant St., Long Beach, CA 90808

Phone : 800-500-3519

Fax : 310-900-1066

www.turboairinc.com

Summary of Contents for TAR-10















Reviews: