8
O
W
N
E
R
'S
M
A
N
U
A
L
•
T
3
0
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually
needed, provided
•
the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to
one side due to the user’s running style (e.g. more
weight on one foot). The alignment of the belt is
adjusted by turning the two bolts at the back of the
treadmill.
ALIGN THE BELT ACCORDING TO THE FOLLOWING
INSTRUCTIONS:
1.
Turn the power switch on and increase the
treadmill’s speed to 5 km/h (3 mph).
2.
If the belt drifts to the left, turn the left adjustment
bolt 1/4 turn clockwise and the right adjustment bolt
1/8 turn anti-clockwise. If the belt drifts to the right,
turn the right adjustment bolt 1/4 turn clockwise and
the left adjustment bolt ¼ turn anti-clockwise.
3.
If the belt remains centered the adjustment is
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned. If the belt
is allowed run across to one side for long periods of
time the edges of the belt may be damaged and the
treadmill may not continue to operate correctly. Any
damage to the belt caused by the lack of necessary
adjustment will not be covered by the warranty.
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on the
rollers. In normal use, however, keep the belt as loose
as possible! The belt tension is adjusted by turning
the same screws as used for aligning the running belt.
If turning the screws will not effect the belt tension,
please contact your local Tunturi dealer.
1.
Increase the treadmill’s speed to 5 km/h (3 mph).
2.
Turn both adjustment screws an equal amount, ¼
turn clockwise.
3.
Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill). If the belt slips, turn another 1/4
turn and repeat the test. When braking heavily the belt
may slip. If the belt keeps slipping despite repeated
adjustments, please contact your local Tunturi dealer.
MALFUNCTIONS
NOTE!
Despite continuous quality control, defects and
malfunctions caused by individual components may
occur in the equipment. In most cases it’s unnecessary
to take the whole device in for repair, as it’s usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait
1 minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and
ready the treadmill for normal operation again. If after
you have reset the treadmill by turning the power
switch off and on again, and the treadmill is still not
operational, contact your local Tunturi dealer for
service.
If you require spare parts, always give the model,
serial number of your equipment and the spare part
number for the part you need. The spare part list
is at the back of this manual. Use only spare parts
mentioned in the spare part list.
ERROR CODES
The user interface will display information about
operational faults.
E1:
Speed sensor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
E6, E7:
Lift motor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
PROTECTIVE CIRCUIT
The machine will shut off when the electricity load is
above the machine’s capacity. To restart the machine,
please follow the procedure below:
A.
Unplug the power cord from the machine’s socket.
B.
Push in the safety switch.
C.
Replug the power cord into the machine’s socket.
Safety switch
ON/OFF
Power cord
NOTE! DON’T PUSH IN THE SAFETY SWITCH BEFORE
UNPLUGGING THE MACHINE’S POWER CORD.
If you leave the treadmill plugged in after turning
off the console, there will still be current running to
the console. This treadmill is equipped with a safety
control program that will automatically shut down
Summary of Contents for T30
Page 75: ...75 T 3 0 ...
