manualshive.com logo in svg

TUNA ID551PN, Operation Manual, Page: 29 / 29

Share
Download
TUNA ID551PN Operation Manual Download Page 29

ID551PN

 

Weighing Controller

 

29 

Appendix 2 Display Message & Error Code

 

Display Message &   

  Error  Code 

Description 

CAL_2 

Set Span Calibration 

CAL_0 

Set Zero Calibration 

CAL_35 

Calibration Fail, Check load cell cable or if scale is stability 

CAL_D 

Calibration Done 

CALF-E 

Factory CalFree Calibration data error, have to back to factory 

for Factory Calibration again. 

-EEE 

Power Up Zero Fail for below zero too much 

EEE 

Power Up Zero Fail for above zero too much 

EE - 10 

E2PROM hardware error 

EE - 11 

E2PROM data error 

EE – 100 

Tare failed, Disable Tare   

EE – 101 

Tare failed for scale in motion 

EE – 102 

Tare failed out of tare range 

EE - 105 

Zero failed for Zero is disabled   

EE - 106 

Zero failed for scale in motion 

EE - 107 

Zero failed out of zero range 

EE – 108 

No keys allowed for keypad is locked 

EE - 109 

PLC option board start failed. 

EE - 111 

ADC Init failed, please re-power, or contact factory. 

EE - no 

The product key does not match, please contact the 

manufacturer 

-- 

Lock Display, change F10.F.3 to recover display weight 

SEALEd 

Seal lock, disable change weight parameters and weight 

calibration,

 

Toggle switch to enable seal 

 

Over capacity blank, weight is above scale capacity 9.9d 

 

Under zero blank, weight is under zero 50d 

 

Summary of Contents for ID551PN






























Reviews:

No comments