background image

Transmitter Controls

11

1

2

4

6

8

10

7

9

5

3

Antenna
Flight Mode Switch:
(1) Take Off Mode: When the GPS antenna receives 7 signals from the satellite, it will switch to the 

GPS mode automatically.

(2) Landing Assist: The Landing Assist will automatically decelerate and stabilize the drone when in 

landing, the function will be activated when drone is within 2M from the ground.

(3) Return Home: The Return Home feature will autopilot the drone back to the original take off point 

and proceed the landing automatically.

IOC (Intelligent Orientation Control):
(1) IOC OFF: When IOC switches to the “OFF” mode, the IOC function will be dismissed.
(2) IOC ON: When IOC switches to the “ON” mode, the drone will be heading locked intelligently and 

oriented to its original take off point

Gimbal Angle Knob(Tilt): Trim the Tilt of the Gimbal.
Gimbal Angle Knob(Roll/Pan): Trim the Roll or Pan of the Gimbal.
Joystick
Binding Button
Stick Mode Switch:
(1) MODE 1:
(1-1) Altitude Control (CH 3) is at right joystick/ Up and Down. 
(1-2) Forward/Backward Control( CH 2) is at left joystick/ Up and Down.
(2) MODE 2:
(2-1) Altitude Control (CH 3) is at left joystick / Up and Down.
(2-2) Elevator Control (CH 2) is at right joystick/ Up and Down.
Power Switch
Charger Jack
Reract Landing Skid Switch: 
To control the Retract Landing Gear uplock / downlock.

1.
2.

3.

4.
5.
6.
7.
8.

9.

10.
11.

2

Summary of Contents for Commander











Reviews: