manualshive.com logo in svg

TT Robotix Commander, Instruction Manual

Share
Download
TT Robotix Commander Instruction Manual Download Page 2

Introduction

1

Congratulations  on  your  purchase  of  the  Commander  advanced  2.4GHz  spread  spectrum  radio 
control system. This system was specifically-designed with the latest wireless and Thunder Tiger 
advanced-programming  technology  to  meet  R/C  model requirements. With spread spectrum and 
smart  frequency-hopping  system,  the  Commander    radio  system  delivers  precision  &  reliability 
control without any interference risks.  

Features

■

■

■

2.4GHz Frequency hopping spread spectrum wireless system
Built with advanced frequency hopping program on the spread spectrum base to deliver system 
safety and reliability without interference risks.
Security ID binding link
A binding feature is included with the Commander  2.4 GHz spread spectrum system ensuring 
transmitter and receiver only recognize each other to prevent interferences from other controllers. 
Range checking function
A range checking button on the transmitter reduces transmitter signal for pre-flight range check. 
It is recommended to perform range check before every flight.

System Contents

Specifications

Item No.
Configuration
Encoder
Frequency(GHz)
Modulation
Current Drain
Frequency Band Width
Transmission System
Antenna Type
Antenna Peak Gain
Power Requirement
Dimension (w/o antenna)
Weight (g/oz)

Commander

8901
Dual Sticks
9Ch
2.4GHz
GFSK
[email protected]
2402~2479MHz
FHSS

1/4λDipole Sleeve

2dBi Typical
7.2V/6 cell AA Battery
180 x 180 x 70mm
435g / 15.37oz

Receiver

Frequency(GHz)
BEC
Type
Antenna Type
Battery Power
Dimension(mm)
Weight(g/oz)

TRS901DD

2.4GHz
No
PPM
Dual Antenna & Diversity 
4.8~7.4V
29.2 x 44.9 x 14.1
10.5g / 0.37oz

Transmitter

Transmitter

Receiver

Manual

1

Summary of Contents for Commander











Reviews:

No comments

Brands by name

Popular brands

Load more brands