Tsurumi Pump OM Operation Manual Download Page 5

Page: 5 / 15

-4-

2 PART NAMES

3 PRIOR TO OPERATION

Example

Check the following points after unpacking the package:

Inspecting the Product

Verify that no damage has occurred to the pump during shipment and that the bolts and

nuts have not loosened.
A certain automatic pump has a piece of tape afﬁxed to the ﬂoat case, in order to prevent it

from becoming detached during transport. Please remove the tape before using the pump.

Inspecting the Speciﬁcations

Check the nameplate of the pump unit to verify that it is the product that you have

ordered. Pay particular attention to its voltage and frequency speciﬁcations.

Inspecting the Accessories

Verify that the following accessories are included in the package:

Operation Manual ....................1

Note:

If you discover any damage or discrepancy, please contact the dealer where this

equipment was purchased, or the Tsurumi sales ofﬁce in your area.

Cabtyre Cable

Mechanical Seal

Oil

Impeller

Oil Plug

Strainer Stand

Upper Pump Casing

Air Valve

Bearing Housing

Lower Pump Casing

Float Case

Automatic type

Tape

Summary of Contents for OM
















Search results

Summary of Contents for OM

Reviews:

Related manuals for OM

Brands by name

Popular brands

Tsurumi Pump OM, Operation Manual

Search results

Summary of Contents for OM

Reviews:

Related manuals for OM

Brands by name

Popular brands