TSI Instruments AEROTRAK 9306 Page 69 Operation Manual Download

Page: 69 / 82

5-1

C H A P T E R 5

M a i n t e n a n c e

The chapter contains maintenance and troubleshooting solutions for the
Model 9306 AeroTrak

Handheld Airborne Particle Counter.

NOT I CE

There are no user-serviceable parts inside this instrument. Opening the
instrument case may void the warranty. TSI

recommends that the

AeroTrak

Airborne Particle Counter be returned to the factory for any

required maintenance or service not described in this manual.

M a i n t e n a n c e S c h e d u l e

TSI

recommends annual factory cleaning and calibration for the

AeroTrak

Airborne Particle Counter. See

Chapter 7, "Contacting

Customer Service"

for service/calibration.

Recommended Field Maintenance Schedule

Item

Frequency

Zero check

Daily or according to application.

Factory cleaning and calibration

Annually.

Cleaning the instrument enclosure

As needed.

Z e r o C h e c k

The zero check ensures that the instrument is properly assembled and
free from leaks, residual particles and electronic noise.

C l e a n i n g t h e I n s t r u m e n t E n c l o s u r e

To clean the enclosure, dampen a lint-free cloth and gently wipe the
surface until surface contamination is removed.

Summary of Contents for AEROTRAK 9306



















































































Search results

Summary of Contents for AEROTRAK 9306

Reviews:

Related manuals for AEROTRAK 9306

Brands by name

Popular brands

TSI Instruments AEROTRAK 9306, Operation Manual

Search results

Summary of Contents for AEROTRAK 9306

Reviews:

Related manuals for AEROTRAK 9306

Brands by name

Popular brands