TSI Instruments AEROTRAK 9306 Page 23 Operation Manual Download

Page: 23 / 82

3-1

C H A P T E R 3

O p e r a t i o n

The Model 9306 AeroTrak

Handheld Airborne Particle Counter is

controlled using a touch screen display.

NOTICE

Use the plastic stylus or your finger tip.

NOT

use sharp objects

(such as a pen point) that may damage the screen overlay.

To turn on the instrument, press the

on/off

button (located in the center

of the front of the instrument). After a splash screen displays the TSI

logo, a brief start-up sequence begins as the Windows

CE operating

system boots up.

The instrument is ready for operation when the

Main

tab (shown below)

appears. If an optional temperature/humidity probe is attached, those
values will be shown in the upper-left corner also.

Summary of Contents for AEROTRAK 9306



















































































Search results

Summary of Contents for AEROTRAK 9306

Reviews:

Related manuals for AEROTRAK 9306

Brands by name

Popular brands

TSI Instruments AEROTRAK 9306, Operation Manual

Search results

Summary of Contents for AEROTRAK 9306

Reviews:

Related manuals for AEROTRAK 9306

Brands by name

Popular brands