TSC TX200 Series User Manual Download Page 56

Page: 56 / 73

- 47 -

6.5

Sensor

This option is used to calibrate the selected sensor. We recommend calibrate the sensor before

printing when changing the media.

Item

Description

Default

Auto Calibration

Printer will feed 2 to 3 gap labels to calibrate the sensor sensitivity
automatically.

N/A

Manual Setup

In case

“Auto calibration” cannot apply to the media, please use

“Manual setup” function to calibrate the sensor sensitivity.

N/A

Threshold Detect

This option is used to set sensor sensitivity in fixed or auto.

Auto

Maximum Length

This option is used to set the maximum length for label
calibration.

254mm

Advanced

This function can set the minimum paper length and maximum
gap/bline length for auto-calibrate the sensor sensitivity.

OFF

Menu

Sensor

Auto

Calibration

Gap

Black Mark

Continuous

Manual Setup

Gap

Black Mark

Continuous

Threshold

Detect

Auto

Fixed

Maximum

Length

Advanced

Summary of Contents for TX200 Series










































































Search results

Summary of Contents for TX200 Series

Reviews:

Related manuals for TX200 Series

Brands by name

Popular brands

TSC TX200 Series, User Manual

Search results

Summary of Contents for TX200 Series

Reviews:

Related manuals for TX200 Series

Brands by name

Popular brands