TSC TX200 Series User Manual Download Page 19

Page: 19 / 73

- 10 -

2.2.3 Rear View

Note:

* Recommended MicroSD card specification.

SD card spec

SD card capacity Approved SD card manufacturer

V1.0, V1.1

MicroSD 128 MB

Transcend, Panasonic

V1.0, V1.1

MicroSD 256 MB

Transcend, Panasonic

V1.0, V1.1

MicroSD 512 MB

Transcend, Panasonic

V1.0, V1.1

MicroSD 1 GB

Transcend, Panasonic

V2.0 SDHC CLASS 6 MicroSD 4 GB

Transcend

- The DOS FAT file system is supported for the SD card.

- Folders/files stored in the SD card should be in the 8.3 filename format

Power jack socket

RS-232C interface

Ethernet interface

* Micro SD card socket

USB interface

USB host

Centronics interface

External label entrance chute

The interface picture here is for reference only. Please refer to the product
specification for the interfaces availability.

inte

rfa

USB

inter

face

Pri

Summary of Contents for TX200 Series










































































Search results

Summary of Contents for TX200 Series

Reviews:

Related manuals for TX200 Series

Brands by name

Popular brands

TSC TX200 Series, User Manual

Search results

Summary of Contents for TX200 Series

Reviews:

Related manuals for TX200 Series

Brands by name

Popular brands