TSC TX200 Series User Manual Download Page 33 | Manualshive

Page: 33 / 73

background image

- 24 -

4.3 Setting Ethernet by Diagnostic Tool

The Diagnostic Utility is enclosed in the CD disk \Utilities directory. Users can use Diagnostic Tool to setup the

Ethernet by RS-232, USB and Ethernet interfaces. The following contents will instruct users how to configure the

Ethernet by these three interfaces.

4.3.1 Using USB interface to setup Ethernet interface

1. Connect the printer and computer with USB cable.

2. Turn on the printer power switch.

3. Start the Diagnostic Utility by double clicking on the

icon.

4. The Diagnostic Utility default interface setting is USB interface. If USB interface is connected with

printer, no other settings need to be changed in the interface field.

5. Click on the

“Ethernet Setup” button from “Printer Function” group in Printer Configuration tab to setup

the IP address, subnet mask and gateway for the on board Ethernet.

4.3.2 Using RS-232 interface to setup Ethernet interface

1. Connect the computer and the printer with a RS-232 cable.

«
...
31
32
33
34
35
...
»

Summary of Contents for TX200 Series










































































Reviews:

No comments

Related manuals for TX200 Series

BOOKMAN ENC-2046

Brand: Franklin Pages: 22

Brand: Renkforce Pages: 4

Brand: HDWR Pages: 203

Brand: Datalogic Pages: 21

Brand: Lindy Pages: 2

Brand: Unitech Pages: 65

Brand: Colop Pages: 2

Brand: AUDIOLINE Pages: 2

Brand: Banner Pages: 69

Brand: Shintaro Pages: 12

Brand: Optoelectronics Pages: 26

Brand: Optoelectronics Pages: 41

Brand: Gems Pages: 107

Brand: Olympus Pages: 121

Brand: Xcellon Pages: 4

Brand: KDC Pages: 24

au biblio Leaf SP02

Brand: KDDI Pages: 2

Brand: Wasp Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands