background image

          

 

 

 

6

This button combines three functions:  

1. 

PAUSE

 button if the printer is in the Ready status. By pressing the 

PAUSE

 

button: (1) the printer stops at the completion of printing of the current 

label,(2) the 

On-Line 

LED flashes, and (3) the printer holds all data in 

memory. This allows for trouble-free replacement of label stock and thermal 

transfer ribbon. A second depression of the 

PAUSE

 button will restart the 

printer. 

2. 

EXE/INC

 button if in the setup mode. Press 

EXE/INC

 button to increase the 

value of parameters, or execute the selected item. 

FEED/DEC Button

 

This button also has dual functions: Feed one label and decrease the value of 

parameters.  

Press the 

FEED 

button, the printer will advance one label. 

Press the 

DEC

 button to change parameter settings or exit the submenu. 

Stripper/Rewind Plate

 

The stripper/rewind plate can be used for strip and label rewind mode. Please 

refer to the instruction of the sticker on the stripper/rewind plate to install this 

plate. 

Carriage Release Lever

 

When opening the 

Carriage Release Lever, On-Line

 LED

 

is lit off, the LCD 

display shows “Carriage Open”. After engage the carriage release lever, press 

the 

FEED 

button

printer will re-register the label and then shows READY on the 

LCD display, and the screen will return to ready

 

condition. 

Print Head Pressure Adjustment Knob

 

  
 The 

print head pressure adjustment knob 

has 5 levels of adjustment.  Because 

the printer’s paper alignment is to the left side of mechanism, different media 
widths require different pressure to print correctly.  Therefore it may be necessary 
to adjust the pressure knob to get your best printout quality. For example, if the 
label width is 4”, adjust both print head pressure adjustment knobs to the same 
level. If the label is less than 2” wide, increase the left print head pressure 
adjustment knob and decrease the right side pressure to level 1. 

 

Ribbon tension adjustment knob 

 

The 

ribbon tension adjustment knob

 offers 6 levels of tension to apply to 

Summary of Contents for TTP-248M
































Reviews: