Trycom Technology TRP-C36 User Manual Download Page 4 | Manualshive

Page: 4 / 26

Trycom Technology TRP-C36 User Manual Download Page 4

2-3. LED Indictor

PWR-:

Power LED

LINK LED:

Ethernet Connection

RX LED

: RS-232/422/485 data receiving

TX LED

: RS-232/422/485 data transmitting

DC Jack

: Input from +10V to +30V. (Pleas use the 5.5*2.1*12 mm DC JACK).

2-4. Reset Button

Return to the factory default, user may find the button between the 2-pin terminal block and

RJ-45 port.

3. Install TRP-C36

3-1

.

Power Connection

Connect power source with TRP-C36. The TRP-C32 has a two pins terminal block and power

jack. Power can apply on either terminal block or the power jack. It su10-+30V

DC/500mA power supply. When power is properly supplied the PWR LED will run indicating the

power is up reading.

Warning: User can only choose one of 2 power source, External DC-Jack or Screw terminal DC

input. Do not use external DC-Jack and screw terminal DC input simultaneously

3-2. Ethernet Connection

A straight-through Ethernet cable can be used to connect TRP-C36 to an Ethernet hub, switch,

or wall plate. A crossover Ethernet cable can be used to make a connection directly to the NIC

(Network Interface Card) on a PC or laptop. When the cable connection properly be made the

“LINK” LED will turn on.

HUB to HUB: Using crossover Ethernet cable.

«
...
2
3
4
5
6
...
»

Summary of Contents for TRP-C36



























Reviews:

No comments