manualshive.com logo in svg

Trycom Technology TRP-C36, User Manual, Page: 12 / 26

Share
Download
Trycom Technology TRP-C36 User Manual Download Page 12

System time elapsed: 

The time elapsed since start of this device in 

[Day Hour: Minute: Second] format. This 

information can be useful in identifying the reliability of system. 

 

Firmware release date: 

TRP-C36 firmware is identified by date code. This information will be required by original 

manufacturer when technical support. 

 

Ethernet address:   

This is an unique MAC (Media Access Control) address used by Ethernet in hex format, 6 digits. 

 

Password: 

This field is the administration password for authentication.   Factory default is empty. However, it 

is not recommended leave it empty in field operation. 

 

TRP-C36 uses the same password protection mechanism commonly used in Windows NT 

or UNIX. If there are more than 3 consecutive times failure in password check during the 

login process, the login function will be disabled, even if user supply correct password, 

the login will not proceed. This prevents intruders find password by computer to generate 

program. User may revert TRP-C36 to factory default by pressing reset button, and login 

again. 

5-1. Start to Setup 

After successfully login, the setup page will be shown as following: 

Summary of Contents for TRP-C36



























Reviews:

No comments