background image

Page 6 

For your own personal protection and for the safety of those around you, please read and 
ensure you fully understand the following safety information.  
It is the responsibility of the operator to ensure that he/she fully understands how to operate 
this equipment safely. 

• 

This equipment is heavy and must not be lifted single-handedly, 

GET HELP 

and use suitable lifting equipment. 

• 

Cordon off the work area and keep members of the public and unauthorized personnel at a safe distance. 

• 

Personal Protective Equipment (PPE) must be worn by the operator when ever this equipment is being used (see 

Health & Safety). 

• 

Make sure you know how to safely switch this machine 

OFF 

before you switch it 

ON 

in case you get into difficulty. 

• 

Always switch 

OFF 

the engine before transporting, moving it around the site or servicing it. 

• 

During use the engine becomes very hot; allow the engine to cool before touching it. Never leave the engine running 

and unattended. 

• 

Never remove or tamper with any guards fitted, they are there for your protection.  

• 

Always check guards for condition and Security, if any is damaged or missing, 

DO NOT USE THE TRUXTA 

until 

the guard has been replaced or repaired. 

• 

Do not operate the machine when you are ill, feeling tired, or when under the influence of alcohol or drugs. 

• 

Do not stand the machine on end with the engine running. 

• 

Do not use the TRUXTA to transport people. 

• 

Do not release the brake suddenly when travelling forward at speed with a heavy load as the machine may topple 

forward. 

• 

 (Brake off). Close the throttle if necessary so that engine braking controls the speed.  

Always ensure that when moving downwards on a hill, the machine is travelling in reverse. 

• 

Before refuelling, switch off the engine and allow it to cool. 

 When refuelling, 

DO NOT 

smoke or allow naked flames in the area. 

• 

Spilt fuel must be made safe immediately, by using sand. If fuel is spilt on your clothes, change them. 

• 

Store petrol/diesel in an approved, purpose made container away from heat and ignition sources. 

• 

If fuel is spilt when re-fuelling the tank, wipe off the excess and wait 2 minutes before re-starting. 

• 

Always travel in a straight line. When travelling across a graduated slope, always travel in a forward direction, 

maximum gradient 6 degrees (10%) when travelling across with a TRUXTA. 

GENERAL SAFETY 

Summary of Contents for QUADro Q300G

























Reviews: