True TBB-1-S Installation Manual Download

Page: 1 / 25

............ www.truemfg.com ............

TABLE OF CONTENTS

Safety Information

Safety Precautions

Proper Disposal

Connecting Electricity

Adapter Plugs

Installation / Operation Instructions

Ownership 4

Required Tools

Uncrating 4

Location 5

Leveling Cabinet

Slide Doors

Wire Gauge Cart

Sealing Cabinet to the floor

Electrical Instructions

Direct Draw Draft Arm Installation

9-10

Start-up and Light Switch Location

Temperature Control Adjustment

Shelving & Bin Divider Installation

Storage & Handling

Temperature/Pressure/Tapping 14

Maintenance, Care & Cleaning

Draft Beer Problems

Changing CO

Gas Cylinder

Cleaning Bar System

Cleaning the Condenser

Important Warranty Information

Stainless Steel Equipment Care & Cleaning 20-21

Lightbulb Replacement

Warranty (U.S.A. and Canada ONLY!)

UNDERBAR

REFRIGERATION

CONGRATULATIONS!

You have just purchased the finest commercial

refrigerator available. You can expect many years

of trouble-free operation.

TBB-3G-S

TBB-2

TD-50-18-S

TDD-4

*Spanish, German, French, and Dutch versions included.

TDB-24-48-1-G-1

#894417 • 11/13

INSTALLATION MANUAL FOR

UNDERBAR REFRIGERATION

TRUE FOOD SERVICE EQUIPMENT, INC.

2001 East Terra Lane • O’Fallon, Missouri 63366-4434

(636)-240-2400 • FAX (636)-272-2408 • INT'L FAX (636)272-7546 • (800)-325-6152

Parts Department (800)-424-TRUE • Parts Department FAX# (636)-272-9471

Summary of Contents for TBB-1-S


























Search results

Summary of Contents for TBB-1-S

Reviews:

Related manuals for TBB-1-S

Brands by name

Popular brands

True TBB-1-S, Installation Manual

Search results

Summary of Contents for TBB-1-S

Reviews:

Related manuals for TBB-1-S

Brands by name

Popular brands