background image

21

WARRANTY

The limited warranty set forth below is given by Troy-Bilt LLC (Troy-Bilt) with respect to new merchandise purchased and used in the United 

States, its possessions and territories. 

Troy-Bilt warrants this product against defects in material and workmanship for a period of three (3) years commencing on the date of 

original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This 

limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator’s Manual furnished with 

the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, 

theft, fire, water or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or 

attachment not approved by Troy-Bilt for use with the product(s) covered by this manual will void your warranty as to any resulting damage. 

This warranty is limited to ninety (90) days from the date of original retail purchase for any Troy-Bilt product that is used for rental or 

commercial purposes, or any other income-producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE THROUGH YOUR LOCAL AUTHORIZED SERVICE 

DEALER. To locate the dealer in your area, visit our website at 

www.troybilt.com or www.troybilt.ca, check for a listing in the Yellow Pages, 

call 

1-800-828-5500 or 1-800-668-1238 in Canada, or write to P.O. Box 361131, Cleveland, OH 44136-0019. No product returned directly to 

the factory will be accepted unless prior written permission has been extended by the Customer Service Department of Troy-Bilt. 

This limited warranty does not provide coverage in the following cases:
A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters
B. Wear items - Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars, 

Cultivator Tines, Blades. 

C. Troy-Bilt does not extend any warranty for products sold or exported outside of the United States of America, its possessions and 

territories, except those sold through Troy-Bilt’s authorized channels of export distribution. 

Troy-Bilt reserves the right to change or improve the design of any Troy-Bilt Product without assuming any obligation to modify any product 

previously manufactured. 

No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the 

applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether 

written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product 

shall bind Troy-Bilt. During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth 

above. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.) 

The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. Troy-Bilt shall not be liable 

for incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn 

care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some 

states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of the safety features 

of the product shall void this Warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others 

and their property arising out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the original purchaser, original lessee or the person for whom it was purchased 

as a gift.

How State Law Relates to this Warranty: This warranty gives you specific legal rights, and you may also have other rights which vary from 

state to state.

To locate your nearest service dealer, dial 

1-800-828-5500 in the United States or 1-800-668-1238 in Canada. 

 

TROY-BILT LLC 

P.O. Box 361131 

Cleveland, OH 44136-0019

MANUFACTURER’S LIMITED WARRANTY FOR:

Summary of Contents for TB227 XP

















































Reviews: