Trotec PJSS11-20V Operating Manual Download Page 6

5

EN

Operating manual – cordless pendulum action jigsaw PJSS 11-20V

Residual risks

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Warning of electrical voltage

Work on the electrical components must only be
carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug
from the mains socket and the battery from the device!
Hold onto the mains plug while pulling the power cable
out of the mains socket.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.

Warning of explosive substances

Do not expose the battery to temperatures above 45
°C! Do not let the battery come into contact with water
or fire! Avoid direct sunlight and moisture. There is a
risk of explosion!

Warning of hot surface

The insertion tool might still be hot after the
application. Burn hazard when touching the insertion
tool.
Do not touch the insertion tool bare-handed!
Wear protective gloves!

Warning of hand injuries

Crushing hazard near saw blade and base plate if
handled without due care.
Wear protective gloves!

Warning of sharp object

Parts of the saw blade are sharp. Risk of injuries if
handled without due care.
Wear protective gloves!

Warning

Toxic dusts!
The harmful / toxic dusts produced during operation
pose of risk to the health of the operator and persons
in the vicinity.
Wear eye protection and a dust mask!

Warning

Do not process materials containing asbestos.
Asbestos is considered carcinogenic.

Warning

Make sure not to hit power, gas or water lines when
working with a power tool.
If necessary, use a pipe detector to check the wall you
want to drill in or slit open.

Warning

Risk of injuries caused by flying parts or bursting tool
heads.

Warning

Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the
hands of children.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Caution

Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.

Caution

Keep a sufficient distance from heat sources.

Note

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Summary of Contents for PJSS11-20V























Reviews: