Trotec PJSS11-20V Operating Manual Download Page 10

9

EN

Operating manual – cordless pendulum action jigsaw PJSS 11-20V

Transport and storage

Note

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Transport

For transporting the device, use the transport case included in
the scope of delivery in order to protect the device from external
influences.

Before

 transporting the device, observe the following:

Switch off the device.

Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

Allow the device to cool down.

Remove the battery from the device.

Remove the tool from the tool holder.

If attached, disconnect the dust extraction system from the
device.

The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:

The user may transport the batteries by road without any
additional requirements.

If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.

– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in

a way that it cannot move inside the packaging.

– Please also observe any other national regulations.

Storage

Before

 storing the device, observe the following:

Switch off the device.

Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

Allow the device to cool down.

Remove the battery from the device.

Remove the tool from the tool holder.

If attached, disconnect the dust extraction system from the
device.

Clean the device as described in the Maintenance chapter.

For storing the device, use the transport case included in
the scope of delivery in order to protect the device from
external influences.

Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.

When the device is not being used, observe the following
storage conditions:

dry and protected from frost and heat

ambient temperature below 40 °C

protected from dust and direct sunlight inside the transport
case

Summary of Contents for PJSS11-20V























Reviews: