background image

EN

11

radiant heater IR 2010 / IR 3010

Technical annex

Technical data

Note

Please use a safety fuse (overcurrent protection device)
or a type C circuit breaker.

Parameter

Value

Model

IR 2010

IR 3010

Heating capacity

2000 W

3000 W

Power supply

220–240 V ~ 50/60 Hz

220–240 V ~ 50/60 Hz

Plug type

CEE 7/7

CEE 7/7

Protection class

IP65

IP65

Dimensions (depth x width x height)

165 x 595 x 105 mm

165 x 925 x 105 mm

Minimum distance to walls and other
objects:

top:

bottom:

sides:

front:

50 cm
180 cm
50 cm
50 cm

50 cm
180 cm
50 cm
50 cm

Weight

2 kg

2,5 kg

Disposal

The icon with the crossed-out waste bin on waste

electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

Summary of Contents for IR 2010













Reviews: