Trotec BT22WP Operating Manual Download Page 3

EN

3

smartphone-controllable thermometer BT22WP

Observe the storage and operating conditions (see
Technical data).

Disconnect the measuring cables from the device before
replacing the batteries.

Intended use

Use this device in combination with a terminal device that is
compatible with the installed Trotec MultiMeasure Mobile app.
Only use the device to measure the air temperature and the
temperature of non-aggressive gases and non-aggressive
liquids.
The Trotec MultiMeasure Mobile app on the terminal device is
used for both operation and the evaluation of the measured
values.
Data logged by the device can be displayed, saved or
transmitted either numerically or in form of a chart.
To use the device for its intended use, only use accessories and
spare parts which have been approved by Trotec.

Foreseeable misuse

Do not use the device in potentially explosive atmospheres, for
measurements in liquids or on live parts.
Radio waves may interfere with the operation of medical
equipment and cause malfunctions. Do not use the device near
medical equipment or within medical institutions.
Persons with pacemakers must observe a minimum distance of
20 cm between the pacemaker and the device.
Also do not use the device near automatically controlled
systems such as alarm systems and automatic doors. Radio
waves may interfere with the operation of such equipment and
cause malfunctions. Make sure that no other devices are
malfunctioning during the use of your device.
Any unauthorised changes, modifications or alterations to the
device are forbidden.

Personnel qualifications

People who use this device must:

have read and understood the operating manual, especially
the Safety chapter.

Safety signs and labels on the device

Note

Do not remove any safety signs, stickers or labels from
the device. Keep all safety signs, stickers and labels in
legible condition.

The following safety signs and labels are attached to the device:

Warning of magnetic field

Information marked with this symbol indicates dangers
to the life and health of persons due to magnetic fields.

Disrupted operation or damage to pacemakers and
implanted defibrillators caused by the device

This symbol indicates that the device must be kept
away from pacemakers or implanted defibrillators.

Residual risks

Warning of electrical voltage

There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.

Warning of electrical voltage

Work on the electrical components must only be
carried out by an authorised specialist company!

Warning
Magnetic field!

The magnet attachment can affect pacemakers and
implanted defibrillators!
Always keep a minimum distance of 20 cm between
the device and pacemakers or implanted defibrillators.
Persons with pacemakers or implanted defibrillators
must not carry the device in their breast pocket.

Warning
Risk of damages or data loss due to magnetic field!

Do not store, carry or use the device in the vicinity of
data storage media or electronic devices such as hard
drives, television units, gas meters or credit cards!
There is a risk of data loss or damages. If possible,
keep the highest safety distance possible (at
least 1 m).

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Summary of Contents for BT22WP















Reviews: