Triumph Adler LP 4118 Page 29 Instructions Manual Download | Manualshive

Page: 29 / 50

background image

OPERATION GUIDE

13

4 Loading Software

Ensure the printer is plugged in and connected to the computer’s parallel
or USB port before installing software from the CD-ROM.

1

Switch on the PC and activate Windows.

NOTE:

If the

Welcome to the Found New Hardware Wizard

dialog box

displays, select

Cancel

.

2

Insert the CD-ROM (Software Library) into the CD-ROM drive.

3

The installation program launches
and the

License Agreement

displays.

Select

View License Agreement

to

read the information and select

Accept

to proceed.

NOTE:

If the installation program fails to launch, use

Windows Explorer

to access the CD-ROM and select

Setup.exe

.

4

Select

Install KX Driver

and follow

the on-screen instructions to
complete the software installation.

5

Once the installation is complete, the

Printer Installed Successfully

dialog

box displays.

«
...
27
28
29
30
31
...
»

Summary of Contents for LP 4118



















































Reviews:

No comments

Related manuals for LP 4118

WorkCentre Pro 90

Brand: Xerox Pages: 36

Brand: DNP Pages: 66

Brand: Oce Pages: 222

Brand: Oki Pages: 192

Brand: Oki Pages: 204

Adaptive CMYK+ Kit

Brand: Xerox Pages: 48

Brand: IOGear Pages: 48

Brand: Xerox Pages: 203

Brand: Canon Pages: 164

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 8

Brand: Canon Pages: 99

Brand: Canon Pages: 188

Brand: Canon Pages: 2

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands