background image

T300si electric shower

Power on indicator 

(fig.)

When the electricity supply to the shower is 
switched on at the isolating switch, the start/
stop button surround will light.

Low pressure indicator 

(fig.)

If this indicator flashes, it means the water 
pressure has fallen below the minimum required 
for correct operation of the shower, resulting in 
the low pressure cut-out operating. This switches 
off power to the heating elements preventing 
any maintained temperature rises (water will 
continue to flow) while at the same time the 
‘cold’ indicator will light.
When enough water pressure returns, the ‘low 
pressure’ and ‘cold’ indicators both extinguish 
and the power will automatically be restored to 
the power setting at the time of interruption.

Selector mode indicators 

(fig.)

Next to each control button there is an LED 
which lights up when the button is pressed, 
visually showing which shower mode is in 
operation.

Phased shutdown

In use, when the Start/Stop button is pressed, 
power is switched off to the elements. Water 
continues to flow for a few seconds, flushing 
out any remaining hot water. This makes sure 
the next immediate user will not receive a slug 
of hot water if standing under the showerhead 
when starting the shower. 

note:

 The shower should always be switched off 

in this manner prior to isolating at the double 
pole isolating switch.

overheat cut-out

During normal operation if an overheat 
temperature is sensed, power to the elements 
will be reduced. Water will continue to flow. 
When the temperature has cooled sufficiently, 
power to the elements will be automatically 
restored to the previous setting at the time of 
interruption.

note:

 In normal use, it is in order to leave the 

water supply permanently on to the shower 
unit,  but  as  with  most  electrical  appliances, 

the  unit  must  be  switched  off  at  the 
isolating switch when not in use.

Power on

indicator

High power

indicator

Economy power

indicator

Cold only

indicator

Low pressure

indicator

Fig.

Operating functions

OPERATING FUNCTIONS

Summary of Contents for T300si

































Reviews: