background image

T300si electric shower

Socket

for control

cable

Control

cable exit

Fig.

Fig.

Fig.9

Align the supplied fixing template 

(fig.)

 

with the 15 mm control cable hole already 
drilled. Mark the four fixing holes marked ‘A’ 
on the template. Drill and plug using the plugs 
supplied, or suitable cavity fixings.
Using the screws supplied, secure the mounting 
bracket to the wall 

(fig.)

.

note: 

The mounting bracket must be fitted on 

the surface of the tiles.
The control panel is connected to the remote 
pack by means of a supplied length of control 
cable complete with a plug at either end. Either 
end of the cable can be plugged to the remote 
pack PCB 

(fig.)

 or the control panel PCB.

Cable entry into the control panel is via the 
opening on the back of the main body of the 
control panel. Remove the two screws and 
remove the access panel 

(fig.)

 to reveal the 

connector socket. 
Cable entry into the remote pack is through one 
of the built in cut-outs.
Remove the protective dust covers from both 
ends of the control cable.
Once the cable has been plugged into the socket 
inside the control panel, refit the access panel, 
making sure the cable exits through the slot at 
the bottom corner of the access panel 

(fig.9)

.

ImporTAnT:

 enough free play should be left 

in the cable to allow for future removal of the 
control panel for servicing purposes.

Make sure the cable clamp in the remote pack is 
used to secure the control cable 

(fig.0)

.

Do noT switch on the electricity supply 
until the cover on the remote pack and 
control panel have been fitted.

Hook the control panel over the lugs on the 

Fig.

Fitting the control panel bracket

FITTING THE CONTROL PANEL 
BRACKET

W-015-A

WARNING!

Under no circumstance should the 

control cable be extended or 

shortened, as not only will it impair 

the performance of the shower but 

will also invalidate the guarantee.

Summary of Contents for T300si

































Reviews: