Triton T22i Installation And Operating Instructions Manual Download Page 10

Shower pump

note: 

If care has been taken to prevent any 

obvious debris entering the system, the above 
procedure should be adequate for normal 
operating conditions of the pump and shower. 
However, it may be advisable to also clean the 
filters in the inlet ports of the pump as an extra 
precaution.

ClEaNING

Clean the unit with a damp cloth using clean 
water or mild liquid detergent.

DO NOt use acid or abrasive detergents.

COmmISSIONING

Before the first operation of the shower pump, it 
is necessary to flush out any system debris from 
the installation. This operation must be carried 
out with the pump isolated from the electricity 
supply, and with the pump feed pipework from 
the cistern and cylinder directed to waste by 
connecting a suitable length of hose.

Procedure

1.

  Make sure the isolating valves from the 

cistern and cylinder are closed.

2.

  Turn on the mains water supply to the 

storage cistern and allow the cylinder and 
system to fill.

3.

  Open both isolating valves and flush 

through thoroughly.

4.

  Allow water to flow to waste for two or 

three minutes to make sure any installation 
debris and air is completely flushed from 
the system.

5.

  Check the system pipework for leaks.

6.

  Close both isolating valves. Remove the 

waste hoses and connect the cistern supply 
pipework and cylinder pipework to the 
pump inlet flexible push-in connectors.

7.

  Remove the showerhead from the mixer 

valve hose and direct the hose to waste.

8.

  Open the mixer valve fully and then re-open 

both isolating valves.

9.

  Allow water to flow under gravity from the 

hose for a few minutes.

10.

  Stop the flow at the mixer valve.

11.

  Switch on the mains electricity supply to the 

shower pump.

12.

  Open the mixer valve. The pump will 

operate and water will flow. Allow water to 
flow to waste for two or three minutes.

13.

  Check system pipework again for leaks.

14.

  Turn off the mixer valve — the pump will 

switch off and the water will cease to flow. 
Replace the showerhead onto the shower 
hose. 

15.

  Switch off the electric supply to the pump 

and eliminate any leaks.

Summary of Contents for T22i

















Reviews: