6
GB
n) NEVER use your hands to remove sawdust, chips or waste close by the bit.
o) If you are interrupted when operating the drill, complete the process and switch
off before looking up.
p) Where possible, use clamps or a vice to hold your work.
q) Examine the chuck regularly for signs of wear or damage.
Have damaged parts
repaired by a qualified service centre.
r) ALWAYS wait until the drill has come to a complete stop before putting it down.
s) Periodically check all nuts, bolts and other fixings and tighten where necessary.
Product Familiarisation
1) Chuck
2)
Quick-Release Collar
3)
Torque Adjustment Collar
4)
Speed Selector
5)
Forward/Reverse Selector
6)
Battery Release Grips
7)
1.5Ah Battery
8)
Trigger Switch
9)
LED Guide Light
10) Magnetic 6mm/¼” Hex Drive
11) 1hr Battery Charger
Accessories (not shown)
1 x 1.5Ah Battery
1 x Soft Carry Case
Intended Use
General purpose drill for driving screws and for light drilling applications (excluding masonry).
This drill is optimally configured for driving screws and fasteners.
Unpacking Your Tool
Carefully unpack and inspect your tool. Familiarise yourself with all its features and functions
Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
• This drill driver has been shipped in a low-charge condition. Charge the battery before
use
Battery charger operation
• The charger and battery may become warm while charging. This is normal and does
not indicate a problem
• Use the charger at normal room temperatures whenever possible. To prevent
overheating, do not cover the charger and do not charge the battery in direct sunlight or
near sources of heat
If the battery does not charge properly:
• Check current at power outlet by plugging in a lamp or other appliance
• If charging problems persist, have the drill, battery and battery charger checked by an
electrician or a power tool technician
Battery Charger Safety
Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before attempting
to charge the battery.
• Do not attempt to use the charger with any batteries other than those supplied. Keep your
battery charger clean; foreign objects or dirt may cause a short or block air vents. Failure
to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard
Warning: Do not recharge non-rechargeable batteries
Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries provided with this
power tool, or others recommended by the supplier. Keep batteries clean; foreign objects
or dirt may cause a short. Allow batteries to cool for 15 minutes after charging or heavy
use. Failure to follow these instructions may cause overheating or fire.
• When not in use batteries should be stored at room temperature (approx 20˚C). Ensure
that batteries cannot accidentally short in storage.
Battery and charger safety features
The battery and charger are fitted with a number of safety features which may be triggered
during charging or operation:
• Over-charge protection: Charger automatically switches off when the battery has reached
full charge capacity, protecting the internal components of the battery
• Over-discharge protection: Prevents the battery from discharging beyond the
recommended lowest safety voltage
• Over-heat protection: Sensor switches off the tool if the battery becomes too hot during
operation. This can happen if the tool is overloaded or being used for extended periods
of time. Up to 30 minutes’ cooling time may be required, depending on the ambient
temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum current
draw is exceeded, protecting the internal components. The battery will resume normal
operation when the current draw returns to a normal safe level. This may take a few
seconds
• Short circuit protection: The battery will stop working immediately if a short circuit occurs,
this prevents damage to the battery or tool
Drill Safety Warnings
WARNING
: Important: It is imperative to follow all national safety regulations concerning
installation, operation and maintenance.
a) DO NOT allow anyone under the age of 18 years to use this tool, and ensure that
operators are qualified and familiar with the operating and safety instructions.
b) Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
c) Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal
injury.
d) Hold power tool be insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord.
Cutting
accessory contacting a “live” wire may make exposed metal parts of the power tool
“Live” and could give the operator an electric shock.
e) Battery chargers are for indoors use only.
Ensure that the power supply and charger
are protected against moisture at all times.
f) When using the drill, use safety equipment including safety glasses or shield,
ear defenders, and protective clothing including safety gloves.
Wear respiratory
protection suitable for the work being undertaken. A minimum rating of FFP2 is
recommended. If operating the tool causes discomfort in any way, stop immediately and
review your method of use.
g) Use metal and voltage detectors to locate concealed electric, water or gas lines.
Avoid touching live components or conductors.
h) Ensure that the lighting is adequate.
i) Ensure that the drill bit is securely fixed in the chuck.
Insecure drill bits can be
ejected from the machine causing a hazard.
j) Ensure that the drill bit is not in contact with the workpiece prior to starting up
the tool.
k) Before drilling, check that there is sufficient clearance for the drill bit under the
workpiece.
l) DO NOT exert pressure on to the tool.
To do so would shorten its service life.
m) Drill bits get hot during operation, allow to cool prior to handling them.
T12DD_Z1MANPRO1_US.indd 6
17/11/2014 10:08