Triton NOVA Thermostatic Series Installation And Operating Instructions Manual Download Page 2

Page: 2 / 28

Electric shower

Products manufactured by Triton are safe and without risk provided they are

installed, used and maintained in good working order in accordance with our

instructions and recommendations.

ARNING:

DO NOT

operate shower if frozen, or suspected of being frozen.

It must thaw out before using.

O NOT

operate the unit if the shower head or spray hose becomes damaged.

O NOT

restrict flow out of shower by placing shower head in direct contact

with your body.

O NOT

operate the shower if water ceases to flow during use or if water has

entered inside the unit because of an incorrectly fitted cover.

ARNING:

If restarting the shower immediately after stopping, be aware

that a slug of hot water will be expelled for the first few seconds.

he shower head must be descaled regularly.

it only shower heads recommended by the manufacturer and never fit any

additional device to restrict the water outlet flow.

he outlet must not be connected to any tap or fitting other than those specified.

his appliance is intended to be permanently connected to the water mains and

not connected by a hose set.

suitable double pole isolation switch for supply disconnections must be

incorporated in the fixed wiring circuit in accordance with current wiring rules.

See Electrical Installation section for further details.

Mains water pressure only.

Minimum inlet pressure 100kPa (1 bar) 150kPa (1.5 bar) for 10.5kW

Maximum inlet pressure 1000kPa (10 bar)

This book contains all the necessary fitting and operating instructions for

your electric shower.
Care taken during the installation will provide a long, trouble-free life from

your shower.

PLEASE READ THIS IMPORTANT SAFETY INFORMATION

INTRODUCTION - PLEASE READ

WARNING

his appliance can be used by children aged from

years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience

and

knowledge if they have

been

given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

hildren may not play with the appliance.

leaning and user

maintenance shall not be made by children.

Summary of Contents for NOVA Thermostatic Series





























Search results

Summary of Contents for NOVA Thermostatic Series

Reviews:

Related manuals for NOVA Thermostatic Series

Brands by name

Popular brands

Triton NOVA Thermostatic Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for NOVA Thermostatic Series

Reviews:

Related manuals for NOVA Thermostatic Series

Brands by name

Popular brands