background image

TR-SRL-574

English

Pag. 3

I. PRODUCT DESCRIPTIONS

Thank you for using our company the TR-C-1224. To optimize the performance 

of this product, please read these operating instructions carefully to familiarize 

yourself with the basic operations of this unit. The TR-C-1224 is a unique 48 DMX 

channel. This unit has been tested at the factory before being shipped to you, 

there is no assembly required. It features include:

•Read the instruction in this manual carefully and throughly, as they give important 

information regarding safety during use and maintenance. Please keep this 

manual with the unit, in order to consult it in the future.

II.- WARNINGS

1.  To prevent or reduce the risk of electrical shock or fire, do not expose this 

unit to rain or moisture.

2.  Clearing memory often may cause damage to the memory chip, be careful 

not to initialize your unit frequency often to avoid this risk. 

3.  Only use the recommended AC/DC power adaptor.

4.  Be sure to save the packing carton in case you may ever have to return the 

unit for service.

5.  Do not spill other liquids or water in to or on to your amplifier.

6.  Be sure that the local power outlet match that or the required voltage for your 

amplifier.

7.  Do not attempt to operate this unit if the power cord has been frayed or 

broken. Please route your power cord out of the way of foot traffic.

8.  Do not attempt to remove or break off the ground prong from the electrical 

cord. This prong is used to reduce the risk of electrical shock and fire in case 

of an internal short.

9.  Disconnect from main power before making any type of connection.

10.  Do not remove the top cover under any conditions. There are no user 

serviceable parts inside.

11.  Disconnect the unit’s main power when left unused for long periods of time.

12.  This unit is not intended for home use.

13.  Carefully inspect this unit for damage that may have incurred during 

shipping. If the unit appears to be damaged, do not attempt any operation, 

please contact your dealer.

14.  This unit should be operated by adults only, never allow small children 

tamper or play with this unit.

15.  Never operate this unit under the following conditions:

In places subject to excessive humidity

In places subject to excessive vibration or bumps

In area with a temperature over 45

0

C/113

0

 F or less than 2

0

C/35.6

0

 F

III. CAUTIONS

1.  There are no user serviceable parts inside this unit.

Summary of Contents for TR C 1224































Reviews: