background image

Tritech International Ltd 

 

Seanet System- Sonar Aux MDL Gyro 

 

Issue 2 

TIL – Eng – Spec – 064 

Page 6 of 15 

 

Warranty Statement

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Tritech International Limited

 herein after referred to as 

TIL 

 

TIL warrants that at the time of shipment all products shall be free from defects in material and workmanship and suitable 
for the purpose specified in the product literature. 
 
The unit/system warranty commences immediately from the date of customer acceptance and runs for a period of 365 
days. Customer acceptance will always be deemed to have occurred within 72 hours of delivery. 
 

Note:

 Any customer acceptance testing (if applicable) must be performed at either TIL premises or at one of their 

approved distributors unless mutually agreed in writing prior to despatch. 
 

Conditions: 

 

These include, but are not limited to, the following: 

 

The warranty is only deemed to be valid if the equipment was sold through TIL or one of its approved distributors. 

 

The equipment must have been installed and commissioned in strict accordance with approved technical 
standards and specifications and for the purpose that the system was designed. 

 

The warranty is not transferable, except or as applies to Purchaser first then to client. 

 

TIL must be notified immediately (in writing) of any suspected defect and if advised by TIL, the equipment subject 
to the defect shall be returned by the customer to TIL, via a suitable mode of transportation and shall be freight 
paid. 

 

The warranty does not apply to defects that have been caused by failure to follow the recommended installation or 
maintenance procedures. Or defects resulting from normal wear & tear, incorrect operation, fire, water ingress, 
lightning damage or fluctuations in vehicles supply voltages, or from any other circumstances that may arise after 
delivery that is out with the control of TIL. 
(

Note:

 The warranty does not apply in the event where a defect has been caused by isolation incompatibilities.) 

 

The warranty does not cover the transportation of personnel and per diem allowances relating to any repair or 
replacement. 

 

The warranty does not cover any direct, indirect, punitive, special consequential damages or any damages 
whatsoever arising out of or connected with misuse of this product. 

 

Any equipment or parts returned under warranty provisions will be returned to the customer freight prepaid by TIL 

 

The warranty shall become invalid if the customer attempts to repair or modify the equipment without appropriate 
written authority being first received from TIL. 

 
10 

TIL retains the sole right to accept or reject any warranty claim. 

 
11 

Each product is carefully examined and checked before it is shipped. It should therefore be visually and 
operationally checked as soon as it is received. If it is damaged in anyway, a claim should be filed with the courier 
and TIL notified of the damage.  

 

Note: TIL reserve the right to change specifications at any time without notice and without any obligation to 
incorporate new features in instruments previously sold.

  

 

Note: If the instrument is not covered by warranty, or if it is determined that the fault is caused by misuse, repair 
will be billed to the customer, and an estimate submitted for customer approval before the commencement of 
repairs. 

 
 
 

F167.1 

Summary of Contents for Seanet Series















Reviews: