Fig.1
Fig.2
Fig.3
Fig.4
Slowly lift the clipper up and outward through the hair, cutting only a small amount at a time
(Fig. 1).
Repeat around sides and back of head (Fig. 2+3).
If you desire shorter hair, either change to a lower number attachment comb or apply more
pressure and less lift away from head with the present attachment comb.
This entire procedure requires practice, and it is always better to leave too much hair the first
few haircuts. For the top of the head, you will give a fairly short cut if you use comb 10.4
With the teeth flat against the head, slowly start trimming from the front to
the back. Again, it is better to leave the hair longer the first few haircuts (Fig. 4).
Outlining requires no attachment. Take the clipper and push the lever up to the close-cut
position. Make sure the comer edge of the blade is against the hairline. With the outline of the
hair as your guide, slowly move the clipper over, around, and behind the ears. For the back of
the neck and the sideburns, hold the clipper upside down and holding it against the skin at the
length desired, move downwards.
If a short tapered cut on the sides and back is desired, follow the diagram below:
Use blade lever (no. 4)
The allows you to gradually change the closeness of your cut without an attachment comb.
When the lever is in the uppermost position, the blades will give you the closest cut and leave
the hair very short. Pushing the lever downward gradually increases the cutting length.In its
lowest position, the lever will leave the hair approximately the same length as a comb 10.1.
The lever will also extend the use of your blades since a different cutting edge is used in each
setting.
Claening and maintenance
Always remove the plug from the outlet first. After each use, remove any hair with the cleaning
brush (no. 9) and spread one or two drops of oil (no. 8) on the blades. Use only acid-free oil as
supplied. Unscrew the blades regularly and remove all hair trimmings. When replacing the
blades make sure that they are properly adjusted. The blades are adjusted as follows:
•
Screw the blades back on the clippers, but do not turn the screws
tightly yet.
•
Turn the blade lever to the side downward.
•
Shift the top blade until it is even (parallel) with the bottom blade and
be sure that the two blades are about 1.2mm (1/32 inch) apart.
•
Now tighten screws firmly and make sure that the blades cannot shift.
Clean the outside of the clipper with a clean soft, damp cloth. Never immerce the device in
water or other liquid.Do not place or store appliance where it can fall or be pulled into a tub
or sink.
IMPORTANT SAFEGUARDS
•
Read all instructions before use.
•
Do not touch hot surfaces. Use handles or knobs.
•
To protect against electric shock, do not immerse cord, plug or appliance in water or
any other liquid.
•
Unplug from outlet when not in use and before cleaning. Allow the device to cool
before putting on or taking off parts. Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions, or has been damaged in any
manner.
•
The use of accessory attachments not recommended by the appliance manufacturer
may cause injuries and invalidate any warranty you may have.
•
Do not use outdoors, or on or near direct heat sources
•
Do not let cord hang over edge of table or counter, or touch hot surfaces or come
into contact with the hot parts or allow the product to be situated underneath or close
to curtains, window coverings etc.
•
This appliance is for household use only and only for the purpose it is made for.
•
The appliance must be placed on a stable, level surface.
•
This appliance is an attended appliance, and as such should never be left ON or
whilst hot without adult supervision.
•
This appliance is not intended for use by persons (including children) with reduced
physical,sensory or mental
capabilities,or lack of experience and knowledge,unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
•
Children should be supervised to ensure that they do not play with the appliance.
•
For additional protection, we advise you to install a residual current device (RCD) in
the electrical circuit that supplies the bathroom. This RCD must have a rated
residual operating current not higher than 30mA. Ask your installer for advice.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Guarantee
•
The device supplied by our Company is covered by 24 month guarantee starting on
the date of purchase (receipt).
•
During the life of the guarantee any fault of the device or its accessories to material
or manufacturing defects will be eliminated free of charge by repairing or, at our
discretion, by replacing it. The guarantee services do not entail an extension of the
life of the guarantee nor do they give rise to any right to a new guarantee!
•
Proof of the guarantee is provided by the proof of purchase. Without proof of
purchase no free replacement or repair will be carried out.
•
If you wish to make a claim under the guarantee please return the entire machine in
the original packaging to your dealer together with the receipt.
•
Damage to accessories does not mean automatic free replacement of the whole
machine. In such cases please contact our hotline. Broken glass or breakage of
plastic parts are always subject to a charge.
•
Defects to consumables or parts subject to wearing , as well as cleaning,
maintenance or the replacement of said parts are not covered by the guarantee and
hence are to be paid!
•
The guarantee lapses in case of unauthorized tampering.
