Introduction:
The Video Splitter is a signal booster and splitter that takes video input from a single source and directs it to multiple video outputs for
monitors using analog signals. Extends the distance a signal is sent to about 210 feet.
Features:
•
One video input to multiple video outputs.
•
Transmission distance of up to 210 feet.
•
Suitable for SVGA, VGA, and Multisync monitors.
•
Daisy chain multiple units to increase the number of outputs.
•
Power-save mode, when the computer is off the power indicator LED’s flash.
IMPORTANT NOTE:
This unit is not designed for CGA, EGA or MONOCHROME type monitors or any monitor using a digital video signal.
Specifications:
Power Consumption
DC 9V, 250mA(max)
Maximum Cable Length
210 feet
Signal Type
VGA, SVGA, Multisync Monitor
Slide Switch
Video signal Gain Control
Installation:
Stand-Alone Installation:
1.
Connect the PC’s Video output port to the Video Splitter’s
Video In
port using an HDDB15 Male/Female Monitor
Extension Cable (Tripp Lite # P500-006, P510-006, P510-010 or P510-015).
2.
Connect the Video Splitter’s
Video Out
ports to the input of your monitors either by using the existing cable on the
monitor or by using an HDDB15 Male/Male Monitor cable (Tripp Lite # P502-006, P512-006 or P512-010).
3.
Connect the provided power supply to the Video Splitter and turn on the unit. Your Video Splitter is ready to go.
NOTE: A slide switch located under the Splitter is used to control the Signal Gain (also known as Power Boost). For short
distances, set the switch to “Normal” Gain by sliding the switch toward the front panel of the unit. As the distance between
Splitter and monitor increases, you may need to increase the unit’s Gain by sliding the switch towards the back.
WARNING: Use
ONLY
9V DC in the operation of these devices.
Daisy-Chain Installation:
1.
Connect the
Video Out
port from the first Video Splitter to the
Video In
of the next unit in the chain. Use a standard VGA
HDDB15 Male/Female cable (Tripp Lite # P500-006, P510-006, P510-010 or P510-015).
2.
Connect the power supplies to the Video Splitters and turn the power switch on.
3.
Adjust the Gain Control Slide Switch until you are getting the best video signal.
4.
Repeat steps 1-4 to connect more Video Splitters into the chain.
NOTE: Signal degradations may occur in Video Splitters towards the end of the daisy-chain. This is the only limitation as to
how many units can be daisy-chained together.
FCC Radio / TV Interference Notice
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense. The user must use shielded cables and connectors with this product. Any changes or modifications to this product not
expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
LIFETIME LIMITED WARRANTY
TRIPP LITE warrants its products to be free from defects in materials and workmanship for life. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such
defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be
returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of
purchase. This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF
THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of
equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.
The policy of TRIPP LITE is one of continuous improvement. Specifications are subject to change without notice.
