Tripp Lite AG-6100 Owner'S Manual Download Page 58

Page: 58 / 72

Step 5

Single input model:

Turn OFF the Q1 Input 1 breaker.

Single input model:

Turn OFF the Q1 Output breaker.

Dual input models (Optional):

Turn OFF the Q1 Input breaker and Q2 Input breaker.

Dual input models (Optional):

Turn OFF the Q1 Input breaker, Q2 Input breaker and Q3

Output breaker.

Step 6

The UPS will enter Shutdown Mode and will slowly de-energize. After the UPS powers off, turn OFF the battery breaker (ex-

ternal battery cabinet).

Step 7

The critical load is now supported in Maintenance Bypass Mode.

7. UPS Operation

Input 1

Output

Input 2

S3M160KX/S3M300KX

(160 kVA/200 kVA) Models

S3M100KX/S3M120KX

(100 kVA/200 kVA) Models

Input 1

S3M100KX/S3M120KX

(100 kVA/200 kVA) Models

S3M160KX/S3M300KX

(160 kVA/200 kVA) Models

Summary of Contents for AG-6100









































































Search results

Summary of Contents for AG-6100

Reviews:

Related manuals for AG-6100

Brands by name

Popular brands

Tripp Lite AG-6100, Owner'S Manual

Search results

Summary of Contents for AG-6100

Reviews:

Related manuals for AG-6100

Brands by name

Popular brands