background image

8

Triple Solar assembly instruction PVT heat pump panels March 2020

5. Preparation for pitched roof, tiled roof 

Attention:

See also the Wagner assembly instruction film on the Triple Solar website.

Aligning panels and installing roof brackets

Each panel is supported by two horizontal mounting rails. These are positioned parallel to each other, 

see figure 5.1-a. It is recommended to plan the configuration of panels, pipes and hoses before starting 
the installation. 

Four roof brackets are required per panel. 2 Screws are included per roof bracket; 7,0x50 stainless steel

Attention:

The dimensions in figure 5.1-a are critical. If they are not respected, the warranty on the panels 

will be invalid.

Start with the lower rail of the lower row of panels. Place the outermost roof bracket at 450 mm 

from the edge of the panel field. Spread the rest of the roof brackets evenly with 1000 mm 

distance between them. Maximum distance is 1600mm depending on the size of the field, see 

figure 5.1-b. 

 

Figure 5.1-a sloping roof alignment diagram (dimensions in mm) The lengths can differ per type of panel.

Summary of Contents for M2 300 165 landscape






























Reviews: