manualshive.com logo in svg

Trinamic TMCM-170, Programming And Reference Manual

Share
Download
Trinamic TMCM-170 Programming And Reference Manual Download Page 22

TMCM-170 and TMCM-171 MODULE – Reference and Programming Manual 

  22 

 

Copyright © 2005, TRINAMIC Motion Control GmbH & Co. KG 

 

3.2.3  STAP – Store Axis Parameter 

 

Description: 

Axis parameters are located in RAM memory, so modifications are lost at power down. 

This instruction enables permanent storing of the previously with SAP altered parameter. All 
parameters alterable with SAP – Set Axis Parameter can be stored, except Type 1 – Set Actual 
Position and Type 160 - Re-Initialization of Sine Commutation (refer to 3.2.1). 

 
Internal function:

 The specified parameter is copied from its RAM location the configuration 

EEPROM. 

 
Related commands:

 SAP, GAP 

 
Mnemonic:

 STAP <parameter number> 

 
Binary representation: 

INSTRUCTION NO. 

TYPE MOT/BANK  VALUE 

7 

<parameter number> 

<motor number> 

(don't care) 

 
 

Example: 

store the maximum speed of motor #0  

Mnemonic:

 STAP 4, 0 

Binary:

 

Byte Index 

0 

1 

2 

3 

4 

5 

6 

7 

8 

Function 

Target- 
address

Instruction 
Number 

Type Motor/

Bank 

Operand
Byte3 

Operand
Byte2 

Operand 
Byte1 

Operand 
Byte0 

Checksum

Value (hex) 

$01 $07  $04 

$00 

$00 $00 $00 $00 $0c 

 

 

Note:

 The STAP command will not have any effect when the configuration EEPROM is locked 

 

Summary of Contents for TMCM-170






























Reviews:

No comments

Brands by name

Popular brands

Load more brands