modular
DIM BASIC
The modular
DIM BASIC
module is at the heart of the modular
DIM
concept.
It has three output channels which can individually drive up to 100 DSI
devices (PCA, TE one4all, PCD) and provides power to the extension modules
via the iX interface. DSI devices connected to each channel can be dimmed
or switched via the DSI signal as independent channels or combined as one
group. In addition the modular
DIM BASIC
has three PIR inputs to connect
standard presence detectors with potential free contacts. Each channel can
be switched independantly. One presence detector can be linked to all three
channels via a bridge to the other PD inputs thereby allowing all three
channels to be switched as one.
modular
DIM SC
The modular
DIM SC
is an extension module powered directly by the modu-
lar
DIM BASIC
module. It has been designed to allow the user to recall four
different light scenes. A short push of the momentary switch recalls a light
scene. To store a light scene you must initially set the light levels via the
modular
DIM BASIC
module. A long push (> 10 s) to one of the modular
DIM
SC
momentary switches stores the new light scene. Confirmation that the
scene has been stored will be indicated by the luminaires connected to the
modular
DIM BASIC
module dimming up and down.
modular
DIM LC
The well known modular
DIM
system will be extended by the new designed
modular
DIM LC
which provides the opportunity to integrate common,
commercial of the shelf mains rated “presence detection (PD) units/sensors”
(converts main rated signals into potential free signals based on the galvanic
isolation). The modular
DIM LC
is designed as “to build in unit” for the
integration into a switch cabinet. This unit is easy to install and to
com mission because there is no programming effort.
Therefore this important feature of the modular
DIM LC
gives now the
opportunity to combine the modular
DIM
system with the common,
commercial of the shelf main rated “presence detection (PD) units/sensors”.
* PD 1 – PD 3 potential free in order to the com-contact (because of the
galvanic isolation)
modular
DIM DM
The modular
DIM DM
is an extension module powered directly by the modu-
lar
DIM BASIC
module. It is designed to provide daylight linked control of
the artificial lighting in a room. The daylight value if measured by a daylight
sensor that is connected directly to the modular
DIM DM
module. Daylight
control is across a dimming range of 0 % to 100 %, with each
channel being programmed with its own dimming characteristic. Channels
can be controlled independently or as combinations of channels. The
auto matic daylight linked control can be disabled via an external switch
(switching contact open
→
daylight function active / switching contact
closed
→
daylight function inactive).
Technical description
The modular
DIM
lighting control system consists of three modules. The modular
DIM BASIC
module, which acts as a group controller and power supply to
the two remaining modules. The modular
DIM SC
module for recalling light scenes and the modular
DIM DM
daylight linked module.
iX
com
All
L
N
com
D2
D1
D2
D1
D2
D1
X2
X1
PD
G 1
G 2
G 3
DSI out
G 1
G 2
G 3
120-277V
max. 100 PCA/TEL/PHD
Ta: 0-50°C
PD
PD
86454539
lux
CONTROL
modular
DIM BASIC
50/60Hz
iX
Active Group
Man./Auto
1
2
3
1+2
1+3
2+3
all
S2
S1
DAYLIGHT
Sensor
modular
DIM DM
86454564
lux
CONTROL
S1
S2
Sx: push to make switch scene
Lx: scene indication output
S3
S4
L1
L2
L3
L4
iX
X2
X1
com
86454545
lux
CONTROL
modular
DIM SC
use only in combination with
lux
CONTROL
modular
DIM BASIC
Ta: 0-50°C
5
Data sheet 08/14-CO061-3 We reserve the right to make technical changes without prior notice.
PD3
com
PD1
PD2
L3
N
L1
L2
modular
DIM LC
86457888
Line Converter
PD out for
modular
DIM BASIC
230V 50/60Hz
PD' switched line
lux
CONTROL
*
*
*
*
