Tridonic luxCONTROL DaLI Msensor 5DPI 14 Product Manual Download | Manualshive

Page: 1 / 52

background image

V052019

Ce produit doit être installé par une personne qualifiée.

S’assurer de la compatibilité des produits suivant son environnement.
La mise en œuvre de l’appareil doit se faire selon les règles de l’art. Nous déclinons toutes responsabilités et nous nous réservons le droit d'annuler la garantie du luminaire en
cas d’installation non conforme, ne respectant pas les préconisations, ou modifiant les caractéristiques de l'appareil. Conserver ce document pour toute utilité future.

EVA

CENTRIC

Tension d'alimentation: 220-240V +/- 6%
Fr

é

quence: 50/60Hz

CRI80 / CRI90 / TNW
NW: 4000k; CW: 5000K: WW: 3000K

EN60598-1

EN60598-2-1 EN 62471-RG0

EN61000-3-2 EN61000-3-3 EN55015 EN61547

NOTICE D'UTILISATION

Ce symbole indique que ce produit ne doit pas être mis au rebut avec les déchets ménagers classiques selon la législation européenne 2012/19/EU. Pour limiter les

risques pour l’environnement et la santé entraînés par le rejet non contrôlé des déchets et afin de promouvoir une réutilisation de ces matériaux, les produits

doivent être recyclés. Pour cela, utilisez les réseaux de collectes de votre région ou prenez contact avec votre revendeur.

Luminaire ne pouvant être recouvert

d’un matériau isolant thermique

Fixation du luminaire

Les modules LED ne sont pas remplaçables. En cas de défaillance le produit doit être changé sous réserve d'acceptation du fabricant.

Version 5P

1) Insérer c

â

ble d'alimentation électrique par le

trou prévu à cet effet puis effectuer les

branchements sur le connecteur rapide.

Pour le branchement

électrique

utiliser un

câble

d'alimentation conforme 60227IEC 52/EN50525
0-75-1.5mm²

2) Vérifier branchements et refermer la languette.

Branchement réseau: Raccorder la phase et le neutre
sur le bornier.

Faux plafond

1)

Accrocher le filin de sécurité sur

un support solide.

2)

Effectuer les branchements

é

lectriques. (ci-dessous)

3)

Poser les encastrés sur

les porteurs du faux plafond

Languette de connexion

Version 3P

AVANT DE COMMENCER LES BRANCHEMENTS COUPER L'ALIMENTATION ELECTRIQUE

Le luminaire doit être install

é

à une hauteur supérieure de 2.35m du sol;

Pour utilisation en intérieur uniquement;

8 RUE JOHANNES BRAHMS
63200 RIOM FRANCE

Branchements

é

lectriques

Entretien et fin de vie

Maintenance du luminaire:

1) C

ouper l'alimentation électrique

2)

Avec un tissu antistatique sec, dépoussiérer le diffuseur et l'enveloppe sans ouvrir

le produit.

Ceci peut garantir un meilleur rendement et réduire la consommation du

luminaire.

Fin de vie:

1) Couper l'alimentation électrique.
2) Enlever le(s) luminaire(s) de son support de fixation
3) Rapprochez-vous de votre mairie pour localiser les centres de collectes

www.electraworld.fr

1
2
3
...
»

Summary of Contents for luxCONTROL DaLI Msensor 5DPI 14





















































Reviews:

No comments

Related manuals for luxCONTROL DaLI Msensor 5DPI 14

Brand: Microchip Technology Pages: 37

Brand: 2gig Technologies Pages: 4

Brand: 2gig Technologies Pages: 2

Brand: G1SLE Pages: 2

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: Walimex Pro Pages: 68

Brand: Magnescale Pages: 3

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Tamas Pages: 12

Brand: Taoglas Pages: 2

Brand: Voltech Pages: 8

Brand: Reliance Foundry Pages: 3

Brand: Wesa Pages: 8

Brand: Anilam Pages: 31

Brand: Rinnai Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands