Protective gloves symbol:
Always wear protective gloves, to avoid the risk of serious injury to your hands.
Warning symbol:
Carefully read the sections marked with this symbol and observe the indications, for the safety
of the operator and the machine.
Covered place symbol:
The operations preceded by this symbol must always be carried out in a dry, covered area.
Symbol for squeegee movement to “work position”:
Indicates the rotation direction of the squeegee control knob in order to bring the squeegee
rubbers into contact with the floor.
Symbol of the open book with i:
Indicates the need to consult the instruction manual.
Main switch symbol:
Used on the central rear of the machine to indicate the main switch.
Recycling symbol:
Tells the operator to carry out the operations in compliance with environmental regulations in
force in the place where the machine is being used.
Tank drainage symbol:
Informs the operator that the recovery tank must be emptied every time the solution tank is
filled.
Recycling symbol:
Carefully read the sections marked with this symbol in order to fill the solution tank correctly.
Tool symbol:
Indicates the need to use tools not included in the supply.
Lifting point symbol:
Used to indicate the location of the elements for lifting the machine or else moving the mobile
parts of the machine.
“OPEN” symbol:
Used on the upper part of the appliance to indicate the position of the handle for opening the
front carter.
Warning symbol not to rotate the machine:
indicates that the machine must not be rotated when the tanks are full.
Explosion risk symbol:
Indicates that the battery may explode in certain conditions, if not handled in accordance with
the directives indicated in the manufacturer's manual.
The descriptions contained in this document are not binding. The company therefore reserves the
right to make any modifications at any time to elements, details, or accessory supply, as considered
necessary for reasons of improvement or manufacturing/commercial requirements. The reproduction,
even partial, of the text and drawings contained in this document is prohibited by law.
The company reserves the right to make any technical and/or supply modifications. The images
are shown as reference only and are not binding as to the actual design and/or equipment.
Symbol of the open book:
used to tell the operator to read the manual before using the machine.
Solenoid valve switch symbol:
Used on the rear of the machine to indicate the solenoid valve control switch.
Disposal symbol:
Carefully read the sections marked with this symbol for machine disposal.
Symbol for squeegee movement to “idle position”:
Indicates the rotation direction of the squeegee control knob in order to raise the squeegee
rubbers off the floor.
SYMBOLS USED IN THE MANUAL
SYMBOLS USED ON THE MACHINE
PURPOSE AND CONTENT OF THE MANUAL
The aim of this manual is to provide customers with all the information needed to use the machine
in the safest, most appropriate and most autonomous way. This includes information concerning
technical aspects, safety, operation, downtime, maintenance, spare parts and scrapping. The operators
and qualified technicians must carefully read the instructions in this manual before carrying out any
operations on the machine. If in doubt about the correct interpretation of instructions, contact your
nearest Customer Service Centre to obtain the necessary clarifications.
TARGET GROUP
This manual is written both for operators and for qualified machine maintenance technicians. Operators
must not perform operations that should be carried out by qualified technicians. The manufacturer is not
liable for damages resulting from failure to comply with this prohibition.
PRESERVATION OF THE USER
The following document must be stored in its special pouch close to the machine, protected from liquids
and anything else that could compromise its legibility.
ON CONSIGNMENT OF THE MACHINE
When the machine is consigned to the customer, an immediate check must be performed to ensure all
the material mentioned in the shipping documents has been received, and also to check the machine
has not suffered damage during transportation. If this is the case, the carrier must ascertain the extent
of the damage at once, informing our customer service office. It is only by prompt action of this type that
the missing material can be obtained, and compensation for damage successfully claimed.
INTRODUCTORY COMMENT
Any machine can only work properly and effectively if used correctly and kept in full working order
by carrying out the maintenance operations described in the attached documentation. We therefore
suggest you read this instruction booklet carefully and read it again whenever difficulties arise while
using the machine. If necessary, remember that our assistance service (organised in collaboration with
our dealers) is always available for advice or direct intervention.
IDENTIFICATION DATA
For technical assistance or to request replacement parts, always give the model, the version and the
serial number (written on the relevant plate).
TECHNICAL DESCRIPTION
The
TRIDENT NM14
is a floor scrubbing machine that cleans a wide range of flooring and dirt types
by means of the mechanical action of a cylindrical brush and the chemical action of a water-detergent
solution, collecting the dirt as it moves forward that has been removed and the detergent solution that
has not been absorbed by the floor.
The machine must only be used for this purpose
.
TECHNICAL DESCRIPTION
This machine was designed and built for the cleaning (scrubbing and drying) of smooth, compact
flooring in the commercial, residential and industrial sectors by a qualified operator in proven safety
conditions. The machine is not suitable for cleaning rugs or carpets. The machine is only suitable for
use in closed (or at least covered) places.
WARNING:
The machine is not suitable for use in the rain, or under jets of water.
IT IS FORBIDDEN
to use the machine for picking up dangerous dusts or inflammable liquids in places
with an explosive atmosphere. In addition, it is not suitable as a means of transport for people or
objects.
SAFETY
Operator cooperation is paramount for accident prevention. No accident prevention programme can
be effective without the full cooperation of the person directly responsible for machine operation. The
majority of occupational accidents that happen either in the workplace or whilst moving are caused by
failure to respect the most basic safety rules. An attentive, careful operator is most effective guarantee
against accidents and is fundamental in order to implement any prevention programme.
SERIAL NUMBER PLATE
The serial number plate is located in the power supply battery
compartment on the rear part of the machine, indicating its general
characteristics, and in particular the serial number. The serial
number is a very important piece of information and should always
be provided together with any request for assistance or when
purchasing spare parts.
8
TECHNICAL DATA
U/M
TRIDENT
NM14
Total power
W
150
Working width
IN
13,4
Working capacity, up to
ft
2
/h
7320
Central brush (number / (diameter x length))
No. /(Øin x in)
1 / (4,3 x 13,4)
Brush motor (rated)
V/W
24 / 50
Vacuum motor (rated)
V/W
24 /100
Maximum gradient
%
2
Solution tank capacity
gal
0,32
Recovery tank capacity
gal
0,26
Machine body length
in
17
Machine body height
in
8,5
Overall dimensions in standby position (L x h x w)
in
15,5x51x17,5
Overall dimensions in idle position (L x h x w)
in
15,5x36x14,4
Rated battery voltage
V / mAh
25.55 / 5200
Battery weight
lb
2,2
Machine weight when empty (m brush + squeegee)
lb
20
Machine weight in transport (m b brush +
squeegee)
lb
22
Machine weight ready to use (m b detergent
so brush + squeegee)
lb
25
Sound pressure level (ISO 11201) - L
pa
dB (A)
<70
Uncertainty K
pa
dB (A)
1.5
Hand vibration level (ISO 5349)
m/s
2
< 2.5
Vibration measurement uncertainty
4%